วีดีโอ

10/10 video! Seen another youtuber say to lubricate the seals with brake fluid during installation. Keep your hands clean, dont want to damage rhe finish with brake cleaner on your hands.

I love the internet. There is probably even a video showing how to put on valve stems (which I ain’t judging lol, only stupid questions are the ones that go unasked)

Thanks for the Great vid, Tip to guys doing earlier models without the abs pump, The location of the rear or front lines into the distribution box is different, Remove the cruise control box, remove the master cylinder and anything else cause it is a real pain getting your hands in there.

The plug you call a drain plug is the screen cover.Stick you finger in the hole and you can pull the screen out to clean it. It's important to clean the actual oil drain plug on the bottom of engine because it has a magnet that collects any steel particles that may be present.

good job

Hey I have a big question please

Excellent job on this video. This is the best explanation I've found for installing this unit in my '21 Pilot. Great job on the camera angles for the connections deep in the center console. Thank you very much!

Great video! Considering buying one of these for the kiddos.

Doesn't work for 2001 alero

Just bought this. Glad there's a video because the the print on the back of the packaging is tiny!

I got one of these, you got to start jacking with stuff on these, right out of the box, there slow 🐌 as shit. I hate to do it but off comes the governor and the we will start from there 😮.

Good job on blending. The devil is in the prep and you sent the devil running. Also saved a lot of money.

My clutch is wobbling. Is this normal?

I just bought a 93.. It was idling good. I buy it.. The next day it won't idle worth a damn.. What could that be.. I doubt is coil packs.. I'm thinking plugs wires PCV..?

Pull out on the bottom clips of the panel.

How do you tighten the tensioner pulley? My mower is exactly the same but the tension pulley is super loose and knocking the belt off

Have the same issue but can't seem to find the part anywhere. Do you happen to know the part number?

Recently got a 94 Mazda b2300. Finally checked the codes and it was dpfe and the hoses. After fumbling around I realized I have the dpfe on there with a hose running from the up into intake. No hose for the down. Then realized whoever had it before put a non egr intake on it with a non egr exhuast. There is the little green hose for the egr but no egr valve. What should be my next steps here?

Have you had any issues with the chain? Installing it shown like you did, the front small sprocket is definently out of alignment a bit with the rear sprocket. It cant be shimmed out with washers because that leaves hardly anything to thread onto on the shaft. Maybe I can loosen my motor bolts and get it to shift slightly to the drivers side.

Right on time. Gratitude. My washer is the same but I’ll have to replace it on the next change

Thank You for Making video

A tip : after breaking to oil filter loose, get a freezer zip bag, put over the oil filter. When you unscrew the filter the oil will go into the bag! Way less mess to cleanup 😊

I have the same Buick. Same color interior also. Any hiccups with yours?

Damn! You pin pointed this to the T this is EXACTY what was going on with mine. Were talking a 30 min fix. Thanks for your help

Thanks for the video i read the instructions but its also nice to see it done aswell.

Best video on this mower yet. Nice job friend. Very helpful thank you.

Does not work for 2001 Park Avenue

Your blades are upside down

Your a dummy nobody cares about the deal you got we only care about the fuel line

Very informative. If I could add 1 thing; I noticed you used wheel chocks/ramps. These cars sit very low to the ground. I use 4 inch cap blocks to get underneath. It's the only way to access the oil drain plug or anything else under the engine so set your parking brake and be careful.

Can you do that with an 04???

Looking like raising that engine up would save you a bunck of cutting on your frame. And you can leave that tab, in case you want to go back to the stock application 😮.

Very helpful. Thank you.

I really enjoyed your video. It was very easy to understand and it answered all my questions. Because of your help , I believe I can keep my mower running.

I need advice on how to replace the LIFTGATE Taillight on a 2004 Rendezvous.

I can’t get that damn second plug off. The red lock on the second plug just slides back and you push in like any other damn plug, right? Mine is caked like yours is, but I can’t get her to budge and I don’t wanna bust the plug.

Awesome video, do you know if all of this applies to a 30 series torque converter installed on this same bike?

Is that stock wheel size?

I came here to see removing of the clips…. Bypassed it completely.

Let's just keep building, will yah 😮

"promo sm" 😪

Hay . Any help would be appreciated. 04 Buick rendezvous. Went out today and it was making clicking noise. And the lights were flashing off an on . Someone said it's the alarm for the key fob How do I fix it.???

Thanks for the video ! I bought this exact led brake light as my old led turn signals mounted on the fender lip got ripped off ! I couldn't figure out why i didn't have any turn signals as the wiring was confusing me & now know i need to splice together the 2 black & yellow wires as well as hook up the flasher relay it came with & where to find it! Should be able to get it working now & appreciate this video for helping me figure out what was wrong !

Will this work on a 2006 pontiac montana sv6?

Great Job…gives Me confidence to go out and Get ‘er Done! 😁

Rubber strap wrench worked perfectly for me

Thank you for your service!

Have to try it on my 05 Buick Park Avenue

WOOOOOOOO CONGRATZ MY DUDE 🎉❤

average florda man watering lawn