วีดีโอ

@@pallabdas6742 Troubleshooting Point Style Issues in AutoCAD When point styles aren't displaying correctly in AutoCAD, it can be frustrating. Here are some common causes and solutions: 1. Incorrect Point Style Assignment: * Check Point Style Settings: * Go to the "Point Style" tab in the Properties palette. * Ensure the desired style is selected for the point objects. * Verify Layer Settings: * The layer on which the points reside might have specific point style overrides. * Check the layer properties to see if a custom style is assigned. * Inspect Block Definitions: * If the points are part of a block, the block definition itself might have a specific point style assigned. * Edit the block definition and modify the point style within it. 2. Corrupted Drawing File: * Purge and Regenerate: * Run the PURGE command to remove unused objects and definitions. * Regenerate the drawing to refresh the display. * Save a Copy and Repair: * Save a copy of the drawing and try repairing it using the REPAIR command. 3. Display Settings: * Check Visual Style: * Ensure you're using a visual style that displays point styles correctly (e.g., 2D Wireframe or Realistic). * Adjust Zoom Level: * Zooming in or out too far might affect the visibility of point styles. * Verify Hardware Acceleration: * If hardware acceleration is causing issues, try disabling it temporarily. 4. Custom Point Styles: * Inspect Shape Files: * If you're using custom shape files for point styles, ensure they are correctly referenced and located. * Check the file path and permissions. * Redefine Custom Styles: * If a custom style is corrupted, redefine it using the STYLE command and specifying the appropriate shape file. 5. AutoCAD Version and Updates: * Update AutoCAD: * Ensure you're using the latest version of AutoCAD and have installed all necessary updates. * Older versions might have known bugs or limitations related to point styles. Additional Tips: * Create a New, Simple Drawing: * Test your point styles in a new, clean drawing to isolate the issue. * Consult AutoCAD Help Documentation: * Refer to the official AutoCAD documentation for detailed instructions and troubleshooting steps. * Seek Community Support: * Post your specific problem on forums like Autodesk's or other online communities.

@@vishnumukhi7735 I can try

@@shibbutraveller hi

@gaurangpatel494 job ke liye jagah hai sir apke pass

@@shibbutraveller hoga to batat hu

@@muralishwaran6342 Unfortunately, as an AI text-based assistant, I cannot directly interact with your Leica TS10 to provide specific instructions. However, I can guide you through the general process of setting out a circle using a total station like the TS10, given a center point and radius. Here's a general approach: * Set Up the Total Station: * Ensure the instrument is properly leveled and oriented. * Input the coordinates of the center point of the circle. * Input the Radius: * Use the appropriate function or menu in the TS10's software to input the radius of the circle. * Select the Circle Function: * Choose the "Set Out Circle" or similar function. * Set Out Points on the Circle: * The TS10 will likely prompt you to input the number of points you want to set out on the circle. * The instrument will calculate the angular intervals between the points and display the horizontal angle and vertical angle for each point. * Set up the instrument and prism at each calculated point to mark the circle. Additional Tips: * Check the Manual: Refer to your TS10's user manual for specific instructions and keystrokes. * Coordinate System: Ensure that the coordinate system used in the instrument matches the coordinates of the center point. * Prism Height: Consider the prism height when setting out points to ensure accurate measurements. * Weather Conditions: Be aware of weather conditions that may affect measurements, such as wind and temperature. If you encounter specific difficulties or have questions about your TS10's functions, I recommend: * Consulting the User Manual: This is the most reliable source of information for your specific instrument. * Contacting Leica Geosystems Support: They can provide direct technical assistance and troubleshooting advice. * Seeking Assistance from Experienced Surveyors: Local surveyors who are familiar with the TS10 can offer practical guidance. By following these steps and seeking additional assistance if needed, you should be able to effectively set out a circle using your TS10. Please let me know if you have any other questions.

@@NirmaliVlogs samja nahi aap Kay kahana chate he?

@@gaurangpatel494 jab pre or post level se cross section graph banate hai to pre ka scale or post ka scale same nhi hota h tab us condition mai kay karna chahiy

jaise ki aap ke video mai pre or post ka scale 15 se start hua to wo easy h par ye different ho tab ky karna chahiy is par bhi ek video bany sir ,thank you sir

@@TheWB45Rider please tell me

@@pallabdas6742 please see this solutions www.autodesk.com/support/technical/article/caas/sfdcarticles/sfdcarticles/ARRAY-command-does-not-create-objects-in-Autocad.html

@@kamleshsodhasurveyor.gujra9852 🙏

@@sunilyadav-cf4ql thank you 🙏

@@NirajKumar-dy9eo oky

@@kamarampadmavathi2385 thank you

@@parmeshsingh6508 thank you parmesh aap sabhi ka pyar eese hi bana rahe🙏

@@Sandeepjha1 (session-10 ) 2din pahele dal diy he bhai

@@Sandeepjha1 th-cam.com/video/TEl8lMzAnqs/w-d-xo.htmlfeature=shared

@@Ritikbhai0420 thank you

@@pallabdas6742 as per MORTH (Sections 100)every Month

@gaurangpatel494 sir appka video dekhkor bhot atcha lgta hai

Sir , ak surveyor ka road sector work may kya kya kam hota hai . Please sir point ways bataye 🙏

Kal sehi apka video hi dekh raha hu . Jobbih time mile 🥰

First time in life I understand Easily how to calculate traverse.thnx Sir

@@OmkarThakur-p1p autocad me ?

Dono lone ko Select karo or Joint command Type karo aapki line Joint ho jayegi

@@ravindransci4913 please see this video th-cam.com/video/0pbG9T1SKOk/w-d-xo.htmlfeature=shared

Ek video baneye level kaise dete hain TS se level kaise chake kare Sahi kaam huaa hain ki nahi