![Sykesville Offroad](/img/default-banner.jpg)
- 58
- 25 933
Sykesville Offroad
United States
เข้าร่วมเมื่อ 14 มิ.ย. 2024
Making "adjustments" to our LS SWAP.
The time has come to make some changes. The more I get into working on the details of the motor swap I'm not happy with where the motor is side to side in the chassis. It's time to fix that. 1974 Jeep J10, 4.8LS with a 4l60e with a Squarebody np208 transfer case. # #jeep #thisisfine #garbage #j10 #offroad #motorswap #overlanding #rusty #shoptruck #squarebody
มุมมอง: 5
วีดีโอ
September 2, 2024
มุมมอง 1014 ชั่วโมงที่ผ่านมา
This video describes how I built my own hack and tap slip yoke eliminator for a GM 208 transfer case. I actually tried using a Jeep 208 transfer case that comes factory with a fixed rear output and the tail shafts and rear nose cone were just too different for me to use and have any faith that I wouldn't have any issues. I used what I consider basic tools to get the job done and I am pretty ha...
How I set up my wife's JKU for a two week Overlanding trip. 
มุมมอง 266หลายเดือนก่อน
How I set up my wife's JKU for a two week Overlanding trip. 
EZGO TRASH! #garbage #junk #makesthewifegiggle #3pg
มุมมอง 102 หลายเดือนก่อน
EZGO TRASH! #garbage #junk #makesthewifegiggle #3pg
New Bed Floor On The Old C10. #c10 #garbage #rusty #salvage #rustyrestoration #mechanic #shoptruck
มุมมอง 92 หลายเดือนก่อน
New Bed Floor On The Old C10. #c10 #garbage #rusty #salvage #rustyrestoration #mechanic #shoptruck
Way more than 4 views!
Old flat fender for the win 🥇
Nice. Happy to see your faith in your craft
You have a gassy vapor leak problem?
What is that part?
@@briandalton3297 Evaporative Emissions System Leak Detection Pump. It basically goes on the back of the evap canister under the Jeep.
Looks better than the cab & bed of my 2nd gen ram 🐏 pickup. Cummins drivetrain needs a cab like that❤❤❤❤
Old CJ's always had those weird nut retained axle flange, that nessesitated the big center hole in the wheels. Had a couple of Jeeps, their weird.
That continent has some psycho terrain man, really cool lookin Sweet rigs too
Looks like I file cabinet donated itself to the cause
Badass 68 Chevy Camaro
It’s….fine? 😬
That little Jeep is a beast!
It is fine……. 🔥
Banks…. Buy once cry once.
So stop buying the same headers.
They are too short for heat wrap. Stop putting heat wrap on them
There is no easy way as the primary tubes are so short they are just going to crack. Build block off plates so you can completely purge with inert gas while rewelding to prevent oxidation of the weld on the inside. If you are going to weld them on the inside. Create a sheetmetal box with a removable lid that you can bolt the collector to. Allowing you to purge the box and the outside of the header with inert gas. To weld the inside you meed a lazy susan and magnets to allow you to indicate the tube center so you can spin the sheetmetal box while mig welding the inside like a line bore welding machine.. You may need to create an extended mig tip or curved tip extension to let you get deep in the collector . There are several stainless wire alloys or machineable nickel rod that might be a better weld. A copper pipe fitting might be slit to shrink it slightly to wedge into the tube allowing you more heat in the weld without blowing thru. Lastly. Change that ignition coil. I bet if you open the hood in the dark you will see ting high voltage arcs stealing your spark peak voltage creating misfires that have confounded you.
I'm curious what your reasoning is on the coil?
Hookers!
Stainless
Stainless steel
I have a better solution than wrapping your headers with header wrap. Just don’t do it. The one and only time that I’ve ever done it I was itching for like a week. I HATE that stuff!!
Make a copy yourself of them, Heavy tube
Hooker fab shop vs. Build your own....
I am only guessing but if you have a mean cam with big overlap. Mybe you get ignition fire in your exoust. Does the headers glow red i the dark. I am not an expert but i find your problem intresting.
Motor is all stock. Runs great and no glowing headers.
Build Your Own out of Better Materials.
I like the back seats!
This needs RGBW rock lights!!!
Wish you all the luck in the world,youre gonna need it
Thanks I appreciate it.
The bed look sweet!
You meant that they wanted to be “Safe”, right?