วีดีโอ

It's good to know your Kicker sub is tolerable.

Thanks very much Sir, I've cleaned and flushed the heater core with vinegar, that didn't help. Going to check that actuator now!!

My actuator is making a bunch of noise now

Excellent video sir. I will be doing this repair tomorrow. 99% sure I am having the same issue after using this video to troubleshoot.

Thanks for the video. On my way to buy the new part. Just gave a like and a new sub

It's a heater core. If you only have high it's the resistor. You can use a 1/4 6 point and put your 5/16ths bit in it I'd for some reason you need too.

Dude! This was EXACTLY what I was looking for!

What the heck is so difficult about the factory bolts. Da...

how did the dorman part work out for you. bout took an eye out on their rear wiper arm for my hard top recently. 🤣

That's not an amplifier, that is a crossover.

You still participate in the Covid virus bullshit? Why the masks?

what year TJ? Your dash is different than my 97

BEST VIDEO OF THIS INSTALL! Thanks a lot man

This helped me tremendously. A fantastic supplement to the written instructions that came with the kit. Thank you!

HELLO, MY FRIEND IVE WATCHED 6 VIDEOS ON THIS INSTALL AND YOURS IS EVEN BETTER THAN MPS VIDEO FROM THE MAN.... AND ANY OF THE OTHERS.THANK YOU FROM DOUG

How much is this? You can't get it in China

Is the alternator on a JL 2.0 located in the same area ? Same procedure ? Thanks in advanced

Great video!! Thanks for the info!!

Made my installation so easy - thanks!

Beauty. Cheers

Hi from your Tennessee mom!

Thanks for the video. My heat is barely working and just got it back on the road. Already checked antifreeze lv now this is my 2nd thing to check. Good job or your clear explanations in your video. Subscribed

To the low ph’zetting

Excellent video. Thanks.

Hoping this is what’s wrong with mine, I have the same issue. Thanks for the video!

Thank you! This was exactly my jeeps issue.

Thanks, I'm going to look into this in the morning. Great video

I fixed my heat and ac problem because of this video. Everyone else saying replace the heater core but this is all I needed to do👍🏻

Heater Core not coil

Hey what is the part number here?

Great job on the video! I'll be doing this soon. Thank you.

there is no power in speaker wires battery does not need to be disconnected

I know you've changed to a JK, but I have a TJ question. I've seen other videos where there's a small dome light under the glove box, above the passenger footwell (fixing the resistor that allows fan-speed changes). I'm undoing some changes that the previous owner made as well as fixing a few things. I found what is likely the power lead for that light, but the light is gone. I can't find a replacement, probably because I can't search for it without using the correct name. Any idea what it's "properly" called?

Good videos. I like the narration bits, but it's also good when you speed through some here and there. Nice work.

Great video, it explains everything to make this little job a simple one.

Thanks. Great video. Getting cold here in Cincinnati. It was the same motor for me on my 2000 TJ. Just took it out for now...lol. It automatically closes for full heat. Living the dream!

I can’t get the passenger side on to save my life. These are such a pain in the a$$ to put on. I’ll try again later.

Awesome job, the camera man too👍

Part number? Name of part?

Putting front and rear bumpers on, no problem. Putting handles on... impossible, lol. The job I thought was going to be the simple one today took forever!!! Lol

I wanted a hitch so I sprung for the classic rear bumper with hitch receiver and no d-ring attachments. You can just use a d-ring attachment in the hitch if needed. For the front i removed the jugs, added the corner caps, raptor lined the whole thing, and added 2 round flood lights. Thing is sweet.

Great videos man. Thank you

my heater never turns off in my 05 wrangler...always a little hot coming out...not good for florida

I had the same problem, I solved the problem by setting my Jeep on fire

A million times “Thank you!”❤️

Good morning from your TN, mom!❤️

Um.....where is the "hard top removal" as listed in the title....??

2:12 nope. That's not an amplifier.

if you use new seals on the top these are not quite long enough to get the threads started.

Thank you. Excellent walk through and explanation of troubleshooting steps what to look for at each step of the process. Now that I have seen your video, I suspect my heating issues will be the actuator motor as well but at least now I can investigate and either proceed or eliminate the motor as the problem without having to buy a part that I may not need.