- 110
- 96 424
TheRagge1
เข้าร่วมเมื่อ 6 มี.ค. 2010
วีดีโอ
HW and Vbar Control Touch
มุมมอง 1.2Kปีที่แล้ว
HW esc integrated with Vbar Control and Vbar FBL unit NEO / EVO
KST programing box
มุมมอง 119ปีที่แล้ว
setting the nuetral possition with the box and you don't have to adjust sub-trims on your transmitter works with v6 and v8
Vibration Analyzer
มุมมอง 69ปีที่แล้ว
Ater a crash , Kraken 700 , try to figure out what this values means
1st Buffer Pack 25F V4 81
มุมมอง 670ปีที่แล้ว
testing the new 1st Buffer pack guard the 2 ways of switching it off
Vbar control , rudder stick wrong way
มุมมอง 2383 ปีที่แล้ว
how do I reverse the stick movement on vbct , sorry for the upside down video
Scorpion Tribunus and Vbar Control Touch
มุมมอง 1.5K3 ปีที่แล้ว
Scorpion Tribunus and Vbar Control Touch
pretty dumb video, the guy's an idiot
How the hell do you bind it...the whloe point
how did you set it up in the vbar? can you explain it please?
I followed this video : th-cam.com/video/XwH05ba9TfM/w-d-xo.html&ab_channel=AuggieCopter
oké thank you 👍
That looks like the motor governor is trying to pre-compensate the collective pitch changes too aggressively. Maybe the unusual motor type (it has a lot more poles than a 'normal' motor) has something to do with it.
Awesome
A awesome video
awesome
Did you update the vbar ? they came out with update for raw 420 using neo
i noticed your tail pitch slider moving while apply cyclic, i'm no expert but maybe you have mixing going on in your transmitter or you have to little or too much gain
its because you dont have blades on it, the governor isnt sensing a load so its bouncing between rpms. put the blades on it and hover it, if you still have a tail shake then your tail gain is off.
Maybe it's because the anti-rotation is stiff?
its the governor
how do I fix it
@@TheRagge1 you dont, this behavior is normal without blades installed. What you are seeing is governor precompensation.
I discovered a similar thing last night on my Raw 420.. just swapped booms and did a bench test. I’m using VBAR gov on scorpion esc. I don’t get a shake, like yours, but I can hear the motor reverberating at high and low collective. I do get a tail kick when switching to motor idle. I think the tail shake on yours, if you’re using VBAR gov, might be tail pre-compensation and gov doesn’t know what to do when the heli isn’t moving according to its predictions. Also my tail is super stiff, even after 20+ flights. I’m going to polish the shaft and also see if I can free up the links. I’ve had tail wag since I’ve had the helicopter.
get the shake on both vbar gov and YGE gov ,
I tried and failed at getting my head around the pro version of this. I found the standard one far more useful.
update ur neo or it might be a gyro sensor problem.
@BongoCat_kR6 , I changed the alu casing with the Lyxn alu-case with dempnings inside and the issue is gone ;)
@@TheRagge1 happy to hear that :j
Could it be some sort of tail curve? and since there is no blades it over or under compensate?
vbar gov or esc gov? did you test with tail servo unplugged?
tried both , same problem
@@TheRagge1 dang thats crazy. Have you tried another vbar unit or esc?
Looks like governor gain to high.
thanks will try setting it down abit , its at 20 Defaul , @WestHobbiesRC what are you gain settings thanks
I would try to use ferrit cores on the servo cables to eliminate any interferences. Maybe it works. Or try another way to lay your cables. Hard to say its complicated :) . Looks like the rear servo react to the others.
Did you ever figure out the problem. That's crazy I've never seen that happen till now.
not yet
@@TheRagge1Are you running a hobby wing 80@mp ESC to heli
@@TheRagge1 you might have to recalibrate your Hobbywing ESC
@@nickdean468 I'm running YGE 95 A , it auto calibrates with vbar
Static electricity?
nopp , got good conductivity from the tail block to the front
Where you get the rear antenna mount?
shop.mikado-heli.de/VBar-Elektronik/VBar-Control-Zubehoer/Antennenhalter.htm?shop=k_mikado&SessionId=&a=catalog&t=7568&c=8353&p=8353
If your useing gov without out blades it does that. And I would run tail blade for 5 minutes to loosen up tail dampeners. Polish tail shaft. I just built two of these loveum
I have the same problem. I use nexspor servo..
hmm , I also use nexspor , do you think its the servos
İnş bizulmaz kardeşim
siir may I as the setting of neo with spektrum tx in nitro heli, dont know how to setup the throttle cut
not sure , as I didn't have a nitro heli , I never experimented on how to
Man I love that truck awesome video wow I just shared this with family and friends to subscribe to your channel and give you a thumb up If you don't mind sharing this old old man's video I would appreciate very much we all need to help each other with a hobby we love thanks
I don't mind , thanks that you liked it ;)
May
Awesome I subscribed to your channel awesome love it
Er du norsk? Syntes jeg hørte norsk tv i bakgrunnen på en av dine videoer… 🙂
det var enkelt fix , eg hade feil i reciever selection meni , bruker man SPM4651T så skal man velge SRXL2 i brain software ,
@@TheRagge1 jeg har valgt det, men får fortsatt ikke opp telemetri... 😔
@@lassepettersen8298 vilken esc bruker du , skal har kabel fra ecs data port til brain pin 5 ,
@@TheRagge1 hobbywing, har den kabelen. Har to Kraken 700, og den ene fungerer det. Men den andre med samme oppsett fungerer ikke...
@@lassepettersen8298 ok den som ikke virke , vilken firmware på esc , mår vare den nyaste men ikke vare vbar firmware
Hi. Did you ever find out what the fix was for this problem? I have the same problem…
Hi, where was a problem? I had the same issue. Thank you.
it wasn't an issue at all , was new to the hobby and didn't know that this is normal
After loading from a file, my Sproto program hung and now I do not see ESC SCORPION. Help if you know?
After loading from a file, my Sproto program hung and now I do not see ESC SCORPION. Help if you know?
I bet Spectrum is running the lowest/slowest sd card out there.
how do you bind it...should have started there
on the reciever menu , you choose which setellite and ms you will be using , check the ''prepare for binding'' box the you recycle the power , your sats will be flashing and ready to bind
Hi. I accidentally touched 3 wires of the ESC SCORPION with each other, there was a click and discharge. Now everything works, but now I am very worried, how did I spoil the ESC SCORPION? What do you think ?
if every thing works now , I will guess you are ok , test it on the bench
@@TheRagge1 thanks, but I don't have a test bench. Bench is such a specialized device?
I'm jealous!!!!🤣 Awesome rig setup, I have the Tamiya Aeromax but it's nothing like yours, great job!!!!👏👍☝👏
Get it fixed?
I returned it and got myself YGE 205 A HVT
@@TheRagge1 Cool, hey thanks for your response. Happy flying.
Just turn it around dummkopf! It's upsidedown :)))
By getting a Futaba! :)
Interesting that you use your throttle hold switch for the Motor cutoff. Mikado recommends another, 3 position, switch. Your selection seems to make more sense to me unless perhaps this interferes with autorotation options.
I suppose you have figured out by now that if you put rescue on the Spektrum Blade Rescue/ "Bind" button, the longer you push the button the longer your heli will climb in Rescue Mode. Move it to another switch and toggle on, toggle off.
Ragge, what quick release canopy nuts are you using? RCBooya?
same as this : goblin-helicopter.com/products/quick-release-canopy-knob
Show,,,,,,,,,,,,
????????
900 euros for this??? look at ebay 1:14 scale 224 euro www.ebay.com/itm/Tamiya-MAN-1-14-Showtruck/112981558087?hash=item1a4e39c347:g:mpcAAOSw7I5a8gBJ
can neo v working with hitec radio aurora 9 ??
does aurora use a single line reviever , if so then it should work using UDI , NEO don't work with a fullsize revievers
Does this new tray make the batteries sit higher?
yes , a little
Thank you for the info. Guess I will not be able to use it then as I cant afford to give up any clearance.
Did you figure out what it was? If it was the receiver the servos shouldn't move. Maybe you're having a voltage BEC problem?
I believe it was the brain loosing updates , had to update it 3 time with the same FW , now it seems to behave
TheRagge1 it looks like a BEC issue cause the ultra guard is flashing/dimming.
have capacitor connected to the system , probabbly don't help much