วีดีโอ

pleased show us connection to receiver

very cool vid! Just a question, how did you connect a receiver?

I also have Turnigy Evolution Digital AFHDS . I have paired it with the Eachine UK65 but I'm having problems the drone don't fly only different motors spin at different position and I get Bipping Noise and Red flashing light on the controller. I have this similar controller connected with another drone and it works fine. With the EAchine UK65 it gives me problems.

Hello there, thanks for this Video. I see in the screen on top left side I see the logo of Fly Mode, mode 01 1500. Than the settings logo. On my Screen it does not have Fly Mode Mode01 1500 Option it only has the Settings Logo . How did you managed to get your controller to have the FlyMode Setting?

I noticed that your website is down. Are you no longer offering these kits?

its very sad that he past not to long ago but me and my dad have taken over the drone company

hello i need a help..to configure Fs i6s

I have one. Better to check for bad wiring, hotglued them.

where can you get the all in one 4n1 esc built in a cc3d that sounds crazy?

Motor mount stl file please 😐

Can u pls post a video how to connect naza m lite to fs ia6b reciver tnks in advance

Hi, I have just returned to model making after my retirement, I have a HobbyKing Orx T-6. Everything works fine EXCEPT the ailerons. The right-hand control has no effect on the ailerons on the monitor the pointer does not move. I must have at some time made an adjustment that has affected this. Please can you advise how to return this to travel left and righthand . I hope someone can help with this. the local hobby shop is not keen to help because I purchased this from HobbyKing.

i have an rc plane and i tried to connect my wires to the receiver but it only has the prongs and I have a million wires have you experienced this problem if you have could you tell me how?

i like the XT60 that stays in place on the frame.

Cleaning my workshop. Just came across a few of my old quad lugs 300 & 380 mm. My friend Tom Womack gave me his QLugs he got that was never used. Love to get this old birds in the air again. Ive sold off 1/2 my fpv gear. Trying to refocus on scratch built model planes & experimental aircraft builds.

flysky fs-i6S rssi OSD???

Thank you . Very helpful video to setup my quadcopter with Flysky I6s & Naza. The last failsafe trick was just awesome.

I just figuered out on the dxe If you hold both sticks down and out hold the bind button and turn it on it will sing for a minute.

why cant we just use contact lenses?

Thanks that was super helpful:)

Thanks very much I was successful in getting Manual mode setup in Naza M lite. The problem I had was I was only adjusting the first 2 thousand's and hundred's and not 10th's So I got the Manual mode to turn blue very happy. Now I have to setup failsafe as I had to remove it of the 3 position switch. Thanks again

Hi Are you familiar with the Naza M lite FC? as I wondered if you knew how to get it to use all 4 flight modes with this controller?

Awesome set up demo. Appreciated. I had forgotten how to add a plane in memory. Glad you took the time to do this.

I remember quads like this with wooden dowels.lol😊👍🏻 how far we've come 😊 do you still own it? I bet you haven't flown it in years😊👍👍

Is it the Naza M Lite you were building. Looks very stable :) Thankyou

did you attach the sattelite reciever directly to the special dsmx port added by spedix?

How do you get to fly mode? My Evo doesn't have that on the main screen, or an option for it anywhere in settings, that I can find, has there been an firmware update recently or is that the newer Evo pro controller?

How do you connect FPV camera to the FC?

We hooked this up using the wiring described in the video, and couldn't get the TX to talk to the controller. I checked the Rx with a servo, and it was working fine. I pulled up the website for CC3D, and it had a very different wiring setup that worked. If you run into problems check that site before putting too much time into this. We ended up plugging the 3 connector channel (signal+power) from the controller to the Aeleron signal on the Rx, not the throttle as described in the vid. It's all working now.

I will do something like this but I will use F4 flight controller with INAV.

I'm from Rio de Janeiro, Brazil and I really like your drone projects 🔝🔝🔝

is there a reason you didnt use PPM?

I LIKE IT!

I like this design! Do you think it was made with round dowels it would be more aerodynamic? Wonder if it would flt different? What do you think?

Just have to love the fact that I built mine with you doing this one and I can't wait to try it. I need a battery and the controller radio and then do the final set up with you in this video and I'm off to get it to life off. I am a licensed pilot and have been flying for years and I get the relationship between the alirons and the rudder. But I'll still take it slow and gentle. I'll email you when I'm done and let you know how it goes. Again, Sincerely thank you for your help and this very video.

Beautiful Job!! I have to assemble one of these for our Civil Air Patrol wings STEM kit project and then run through it with the cadets. It's certainly not a toy at all but a serious project. I appreciate you taking your time to do the video and now I know what I'm doing. Wish me luck and thank you.

Link is broken

And can you show me the flysky i6s receiver connection with naza my v2?

Can I use this setup for dji naza m v2 ?

Thanks man. Will check it out. Gpt this kk2 mini on a bag of parts. Gunna build my own soon.

Happy i found this. I just await final part before doing my first build. S500 frame, naza lite with i6s. I never do before. Need all the help i can get. Cheers ............... *QUAD*

I am at the output calibration and have rewired the motors several times. Could someone please clarify how the wires should be orientated? Also, my second motor doesn't begin to rotate until about 1450.

Is there any modifications necessary for the dxe to fly quads

Congratulations! Very nice build! I can't wait for the next video.

I really like your version of the FT Pietenpol. Is the build in 6mm Depron? Looks like it to me. Thanks again for the nice video.

where did you get the lenses from?

Hi o know this is an old thread but do you know where the bootloader pins are for the cc3d on this board?

Very nice. Have not chatted with you in a while. Send me an email when you get a chance.

Anything new with the Rail carbon fiber 250?

Having trouble locating a place to purchase the Scott goggle replacement inserts , any ideas ware they can be found? Thank you.