วีดีโอ

If you do a better job of cleaning it (ie.. grinding wheel) this can be a permanent fix.

Random trap house fixes DIY 😂

Redo the video you moving too much Make your camera stationary

How is replacing the board a step by step to repairing the machine and its original board.....

I wonder if you can weld the crack. Would probably be cheaper to replace the whole pipe.

.......................Thanks 👍

Gona try this as got a old casf iron drain near thd join..and will cover with duck tape.as it has a lot of rain come down ot from the roof.

that is nasty I can only imagine what your home looks like

why did you choose the 750w instead of the 650w ?

one little known fact is that this is one of the rare ryobi charger tt is dual voltage

go to 5 minutes 30 seconds to skip the useless stand assembly

Thank you! I just put my battery on the charger and was wondering how long it would take. Now I know too. 😊

I have the same washer and same board. Also burnt out. It looks like LG is making shitty mother boards and instead of a recall we are all stuck with the $350 motherboard replacement 😡😡😡😡😡😡😡

ya what the last person said .....

Awesome! You make it seem easy to do!

this is replacement not repair. I do hope there is repair video, The used board might cost $200 so not worth to replace.

They need a dehumidifier and a lot of prayer to fix all that.

I fixed a cast iron pipe I have like that 5 years ago

Thank you so much for the video

The blue version (P111) was 10 - 12 hours! 😯

Never mess with old rusty metal without gloves my brother.

Hi thank you for the information! May I know how long you expect the Epoxy Putty could last for a drain pipe? years? or months? Thanks!

I will try this!! I tried expensive tape, although it greatly reduced the water it still didn't fix the problem. I'll try putty plus tape. The putty will get deeper in to the cracks.

Nice video. I currently have a leaky pipe in the basement, coming down from the kitchen sink drain. I’ll try this. You could have a pail of hot soapy water, with a touch of bleach next to you, to clean the area and hands. I think working with the putty with bare hands would be better. I would rather go this route, then to pay a plumber a fortune!

Holy crap.. I got one and it's still half after an hour and a half.. glad I know it's not a dud

Very comprehensive. Thanks

Dear Random: Good video. The epoxy would seemingly be better in any copper situation than duct or electrical tape. Tapes don't fill in the intricately shaped cracks.

Can you use it to divert the air up. Our problem is in the bedroom the only place to put the bed is close to the vent and I want to divert the air up.

Wouldn't that send the air flow onto the floor?

Why are you telling me to nail baseboards pieces and caulking to fill up a space? Really?

what a dump you live in..are you not embarrassed of that filthy place?

Thanks man, 5 years after you posted this and its still helping people out!

So what caused the board to go bad? Won't the new one do the same?

I don't see how this would work as a baseboard diffuser opening is pretty much flush with the wall and the floor vent has an overhang?

Totally left out how to get new diffuser apart in oer to install it. Why?

20 inch is readily available at menards

Dude I bought an old house and this came in clutch!!!

Hi! Can I get your Facebook account? I have some problem with one of regulators exploded. I can't find a replacement of the broken regulator without knowing what kind of regulator that is. There are numbers on it but it exploded so I need your help maybe you could tell me the number of the regulator. I'll tell you which one in the board.

lol that is a lot of putty

Your video is good I am also having a washing machine like this but the panel is not functioning the panel is not supplying the direct drive the diagram is working but the panel is not supplying

Thank you for posting!!

I already replaced the noise filter but still washer not turning on, so i did verified the board and mine seems to be fine nothing burned. Any thoughts what could be?

This is how to Remove the cover to access screw holes for bolting down,(thanks Hank D. in the comments): Hank D 3 years ago Figured it out. Remove the plastic lever cover. Compress the back panel to release the two hooked tabs, along top edge of back panel, then the front panel can slide up (needs slight rearward force also). One side slipped right up, the other needed some encouragement via flat screwdriver from the inside (to avoid scratching the exterior surface)

that's not the only thing needing replacing

Damn that vet Shirley looks cool but it old

Filled that hole with caulking? That’s kind of weird. Why not cut a piece of wood?

It is so slow but it’s compact

What kind of screws did you use (specifications)? What were you screwing through and into (i.e. wall board? 2 x 4?, etc.)?

Looks great! Registers are one of the many overlooked DIY projects that can completely transform the look of your home. There are so many decorative and affordable vents to choose from! :)

Thanks for the video. Our circuit board had a burned spot in the same place. I would not have looked without seeing your video. Thanks again. Order a replacement from Amazon. Fixed withing 2 days.