วีดีโอ

Hello Geri We are updating the software to use PWM output. This will ease spindle control. You can use pwm to analog output for controlling spindle speed.

Thank you very much!

the machine was running at 20mm/Sec. i accelerated the video.

Please refer machine and job settings for more information

Please download the software for freel. You can do all setting for your machine in the Machine settings tab of the software.

No. Raspberry pi 5 is not supported yet. The support will be added soon

Thanks

It's 2500Rs/per License. We can discuss more on quantity.

@@Raspberrypi_CNC_Controller pls contact us

Yes, you can buy the License Also free version is available to download and test your cnc machine to confirm before purchase. Visit: sbc-cnc.com

Not available in current version. Will be added in the next version soon.

Z-Axis probe is added in the latest software. Please download the latest version

Please check your driver. I think your driver is faulty. Its common for stepper motor to heat up as current is passed to hold the load. The software works on raspberry pi 3. Its tested

@@Raspberrypi_CNC_Controller i conected like in picture showed and strarted the software. blue 20, green 19 and red 18 also the gnd but the motor goes only one direktion.... the nemo17 start overheating.. its not normal i guess... but how can i manage so the direktions are correct?

@@snouzz-gaming please refer the manual in the website. You need to set the correct direction pin and also define motor rotation for moving axis in positive direction in machine settings of the software

@@Raspberrypi_CNC_Controller yes, first need be sure, motor coils have sure right connection A coil plus and minus, B coil plus and minus to DM542 driver, motor output. then double check motor current maximum have etc, 3A dip switch change driver 3A or little less. then sure step pin ok, and dir pin ok, and enable pin ok and all grounds. then software confic all pins output and can use good, if hot current have too lot, if noise driver broken or all acceleration and speed etc config have wrong. or motor wired wrong.

@@snouzz-gaming DIR pin on/off move motor direction. need software config all pin right then working well. example id Z axis step pin 20 and dir pin 19 and enable pin 14, you need go to software output pins setup and tell software what pin used step out, dir out, enable or not. and if direction move wrong side setup need invert dir pin output.

You have specific PWM pin numbers highlighted in Machine settings

@@Raspberrypi_CNC_Controller yes, but how to connect the 4 pins to the VFD? or do you need a converter?

@@SHINdanny The 4 Pins outputs 16 possible values; 0000 to 1111. You need to connect these 4 pins to your VFD Controller which will control the Spindle Speed as per the 4 pin combination.

You don't need any code change. This is a complete CNC software which support 3-axis. Please refer other videos from the channel Visit: sbc-cnc.com

No. The software can control only 3-Axis at once. You can use the other IO's to manually control the drives.

@@Raspberrypi_CNC_Controller 4 axis, dont forger can use rotate table too at cnc.

buy mesa super expensive card and make own manual uses software then can.

Yes. You can with G-Code

Hello Jigsey, You only need stepper drivers and Raspberry pi 3B or 4 for controlling your CNC Machine. You don't need any other controllers. SBC-CNC Team

Id assume you shouldnt have a problem as long as you have motor drivers that support the current rating of steppers

if raspi can whit motor controller step and dir system, then can use what size motor controller want, etc my cnc use dm500 about controller and can use max 5A stepper motors.lot torgue, if need biggest stepper motors use DM 800 controlelr ewery motor own can handle up to 8A motor wery strong. stepper motor not matter voltage, but important amperes.

@@sacram1 have many small and big step, dir, motor drivers, TB6600 mac 3,5A motors, dm556 max 5,6A motors DM860 8A motors and motors torgue and Amps have important if orden stepper motors or super expensive servo motors closed loop.

use linuxcnc software and can do lot better all. REALTIME, windows OS and mach3 not can do realtime anythink or GRPL. change arduino to raspberry pi , lot better.

@@mattivirtaSBC-CNC Software can handle this. Please check the channel with latest updates. No need of any CAM software. Just enter the text and carve it.

@@Raspberrypi_CNC_Controller I want to learn the entire process.. Do you know anyone in Mumbai where I can get trained..

@@Raspberrypi_CNC_Controller that's my bad.. Can I know which city you are located?

@@vishalbakshi2816 call me...mob no 9773771057

yes sure but what motor controller boards need use ewery motor, step,dir can send raspi to controller simple. and how all limit SW and E-stop. relays, linuxcnc need use.

linuxcnc ca do all better than GRPL shit. and closed loop servos have totally out of hobby user budget, if normal hobby user stepper motors and drivers cost 200$ servo and closed loop cost 100x more. not hobby users can buy or need be rich men or stupid waste lot money.

@@mattivirta We had a servo that was used to punch holes in 8mm steel plate. When the cost of components reaches certain point you may need to be really putting them to use to generate income or else indeed you will have a very, very expensive industrial grade tool that is not used for industrial manufacturing. Literally owning a factory and having it sit idle.

@@Kameolontti totta, siksi pitäisi aina katsoa oman budjetin mukaiset laitteet, toki parhaimmat mitä voi budjetillaan hankkia on hyvä olla. siksi kukaan selväjärkinen ei osta jotain openbuildin 4000-6000 € konetta kun täysin saman tai huomattavastikin paremman voi itse tehdä pienellä rahalla kotonakin. nuo valmiit cnc koneet on kyllä rahallisesti hullua ostaa jotain 5000€ konetta kotikäyttöön kun se on vähäistä ja kallis investointi, kun voi itse tehdä ihan ajankuluksi saman koneen alle 1500€

normal used gerber file or g-code file not newer rar file.

and linuxcnc download and installing ISO file to pc. but CAM work file need be g-code file

@@Raspberrypi_CNC_Controller which file type for cutting.

@@e-test4938 linux cnc aka emc2 have only best,

all DXF,GERBER,JPG, etc many cam softwares can convert working linuxcnc many FREE softwares have help

CAD / CAM software convert you drawing to G-code and this G-cose can use cnc machine, need CAD software etc. popular have most used "Vcarve pro" and many other software have. you can load CAD picture to convert software or etc, Vcarve can draw you work and this convert automatic you draw to G-code what machine code you use, then cnc machine software can run this code. Vcarve software have windows computer only. but linux have some software too, i not know what name have. i uses Vcarve pro whit windows make parts and convert to G-code and sometime need text file change some row/line in code and then move code to my linux cnc machine usb stick, and run program.