วีดีโอ

Really good video Thx

Lil off topic tryna get some info on the 274cc duromax like what clutch will fit it carb upgrade ect that maddogg tho huh 🔥🔥🔥🔥

If I have the e350 van should I order spacers for a f350?

Nice van. I been watching ir videos how did u lift the back side?

Those are junk water gets in the middle just like you said that how the water gets in

I can struggle faster than that

Just for info!! :) The instruction sheets for EVERYTHING are on the Internet in PDF Format. The only trick is to use the item's "Part Number" when searching and add "PDF" to the search terms. Often the on-line instructions are better and more updated too ...

What fuel pump did you buy?

So how is it now without those, is it still a lot more comfortable

Will it work on grass?

What primary clutch are you using?

Great video! Saved me a lot of time!

I wish I had thought of this before I installed an overhead gauge pod on my G9! I ran the gauge cable inside the windshield strut to conceal it as much as possible. I've been trying to think of a way to get my cart in a covered trailer though, and you just made it look simple! Now, maybe I'll have to re-run my gauge cable so I can copy you!

The point you make about opening the throttle all the way, then removing slack from cable, is exactly correct. That's what I needed to hear. Thanks. This is very helpful.

This is the best swap I've seen. 👍👍👍👍👍

anyone have a amazon equivalent link of this seat ??

Nice

Finally a kayak specific mod that won’t kill the bank with tools I have and materials I don’t need. Thanks a lot

If you over tighten you can drill a bigger hole and use a well nut

Will the 3” work on the front and back?

Well when the silencer and baffle fell out I was losing a lot of compression. In the end it caused my bike to have low bottom end. But my high end went up. At least when I was able to get up to speed.

I removed the cluster pretty much as you di. The three screws almost full out. There doesn't seem to be a threaded hole or pal nut for them to attach to. Any one have an idea what I am talking about? Thank you.

Did you have to do anything with the sway bar? Drop kit, or is it good as is?

Hey C&Q, I bought this same kit for my ‘03 E450, but Ford uses a M20 bolt so the 3/4 thread Extenders don’t fit as you noted. I’m concerned that the smaller dia. 3/4” stud will wear the knuckle spindle oblong. Thoughts? I’m having trouble finding a longer M20 partial thread bolt at 230mm+.

What's the name of the 4 aluminum piece called?

Nice trailer. Towards the end, the video was chopped up.

Yes I did the same idea but I wrapped the bottom frame with a pool noddle then secured it down and that pool noodle halos to raise the seat and seat it back farther in the kayak and gives you even a softer seat ride !! Seat feels great after 8 hours of fishing !!!

Where did your order from?

Didn’t even ride it. Lol

My cart is currently at 12.5 " I would need a step stool to load the wifey up there!

Caliper are made with digital read out HF cheap

I what a 4" lift with 18 ' wheels, old folks find a difficult climbing onto lifted carts. The 6 ' A arm lift is not too expensive for a DS. I can cut 2" out of the spindles. May be hire a pro to do the welding?

I would love a welding demo.

Did use the flux core to extend the spindles? It's obvious that your a good welder.

Looks great

Can we see you drive it? How’s the gearbox holding up

Can the tire be changed for something better to be used on dirt and gravel?

Hi.what did you do to the vacuum hoses

Great idea 👍👍 looking forward to more videos on your golf cart.

Looks good 👍👍

Great video. The link for the spacers claims it will not work on econoline vans with twin I beam front end. Have you experienced any problems?

I’m thinking about purchasing one and can’t find many resources online. Are you part a Reddit community you’re part of by any chance? Would love to pick your brain about the trike and what you’ve upgraded

What size rims and tires do you have?

I just bought one of these for a travel trailer. Thanks for the demo!

Did you get longer shocks or keep the stock ones?

The thing is, i don't trust these heaters in an enclosed space, mass produced, Chinese diesel heater, just asking for carbon monoxide poisoning.

Any idea how it runs on a mud and dirt surface?

wotts at 47 plymouth ?

Will this be compatible with 99 e150 ?

Finally! Someone who knows what they’re doing and I can kinda sorta understand it. 😅😃