วีดีโอ

Same as k20 and k24 engines ?

SMH!

👀🤛🏾😎 Handled like a Boss!! Thank you.🏁🏁🏁🏁

I have same code on my 2015 Buick lacrosse i replaced the Fcpm and air shutter valve code still coming on any ideas

Thx for explaining

you just change the chain and tensioner and solve the code P0017?? I had a elantra 2017 with the same problem and i think thats the fault in the engine, because I inspected the variable gears and I see that they are fine, but the tensioner does not move smoothly. before at all this i replace the exhaust solenoid as it was stuckt, but the signals and voltages are fine. Can you explain me the problem in your case?.

This is not the same flr the honda pilot

I have a 08 Silverado and changed the fuel pump twice and still showing that p069e code and also wants to die on its own. I domt wanna buy the control module if it isn’t the problem

Excellent, Is this for qr25 engine?

Eso que le hecha a las bancada del ciguañal es aceite? Que número es recomendable usar gracias

What year is this scion trying to find timing marks for 2007 scion tc but can't find any your the closest I've been able to find

Sometimes when I'm driving and hit the brake pedal the steering power goes off, do you know what it could be causing this? When I use a scanner tool the codes are 1260 and 2412, if i delete the codes i get power steering for a while and then it fails again

My issue with my 2017 GMC Acadia limited is that it drives fine when it’s cold and a bit warm but once really hot stars to shudder really bad on take off and on reverse would changing the tcm help solve my issue?

Thank you for this video. I’ve done Hondas before about to go tackle one of these this morning. Seems very similar

Thank you

Wow... Literally you did this job single handed and not a torque wrench nor sealant in sight. Amazing..

What car is this for?

Excelente

Stuck on getting the camshaft pulley out Any tips?

mine had bad exhaust phaser took off valve cover, tired moving exhaust Cam, sure enough it rotated freely out of sync with timing assembly. if you go this route don't use a lot of force to move cam bc your turning engine with basically the cam shaft. just enough force to see if free spins and if free spins do not start car afterwards the valves may be damaged. codes p0017, drove like this for a while. i got lucky. about $2000 repair at shop

probably a 2015 for anyone wondering since its not in title or desc

Thank you!!!!!! Tearing back into one I had kid work on for me..... rear head is 180 out..... foook needed verification before busting balls.... hope valves and pistons are OK.

Thanks for your help

How long did this job take?

No explanation or anything. DUMB ASS VIDEO!!!!!

Thank you, so simple got it on the first try.

Thanks for making a video that ACTUALLY shows the real work needed to get it done. Music is annoying though.

how I HATE videos with loud clear noisey music.....yet when the person speaks.....YOU can Never hear them talk

Thanks

Whoever designed this should be horse whipped! Having to disassemble and reassemble all of this just to replace a sensor?!!! It's insane! They couldn't have just put it in a location easy to get to? It's just a money making scheme... most of us would have to carry it to the dealership or Kia mechanic and it probably cost a small fortune to get it done!

Had this motor in a sorento for 80,000 miles at which point the car was sold. Never a problem with it and it was super powerful in that car.

what was the problem ?

Question: My intake cam is set flat for the cam locking tool, but I have to twist my exhaust cam a little bit clockwise to fit the tool in the rear slot. This opens up the exhaust valves slightly on cylinder #2, is this normal?? I have my old head and a rebuilt head, it’s the same. Also, since we took the cam phasers off, how do we set them? I can’t see any marks showing which position they should be in. Mine have numbers 1 and 2 showing on the face, I think 1 is for the intake side…?

This has two different alignment marks in every sprocket, I will put it like the position that you used and I will try it, tanks for share it!

Thank you for your expertise

What grade bearings?

Did you replace or clean it out ?

the engine must come out of the car in order to replace the chain?

Hi i have a p0017 code. Changed both solenoids. Car runs but the code still pops up. No engine knock. But I was told it could be that before they even looked at it what should I tell the mechanic to inspect ?

Do you have another video to explain what part needs to be taking out? I have 2014 Chrysler 300C 3.6 pentastar engine

Might as well just took the whole subframe out your way 🤷🏻‍♂️

hey man, i have a 2018 elantra 2.0L 141.000 miles I have code p0017 and p0014 i stall sometimes at low speed/stop signs/red lights have some trouble start the engine sometimes and it makes a weird noise, it’s also shaking it has trouble up shift gears (takes a long time to up shift), so poor acceleration and rpm jumps because it takes more time to upshift do you have any ideas? thanks! 🙏

Is the new airbag module require programming?

Hello friend, thank you for your video. For the code reader, I would like to know what difference there is between the status '' history " and the status '' present " that the diagnostic cases put for the codes ID

Hello friend, thank you for your video. For the code reader, I would like to know what difference there is between the status '' history " and the status '' present " that the diagnostic cases put for the codes ID

I am still waiting to find out what the problem was. No talking or caption 🤷🤷🤷🤷🤷

can’t see with your hands in the way

You tell people for what you change. Stupid.

You should probably change your music and walk people through it

What all tools did you use