วีดีโอ

some of the transparent stickers are used to hold the light wires down or "lamp wires" (as the manual specifies)

I would request a refund, or at least for them to send you one out 😅

The instruction manual is horrible. This video shows more more than the manual.

I am still assembling mine. I used brown acrylic artist paint for the raw edges. It's fiddle but coming together nicely. I played this video at half speed to get a good look.

This is a combination set, and the music box will be included inside.

What's the song the music box plays, do you know?

I hope this video can help you. Wishing you smooth completion of your project.

@@shuang393Thank you. I haven't finished it yet but I have got the light working (it wasn't as hard as I thought) so I'm feeling pretty pleased about that.

​@@cyflym11 how'd u get the wires into the flower pieces:(

@@queenpotato176 I just stuck a point of my scissors in the hole and twisted it about gently (they are not big scissors and the blades are quite narrow). The plastic is fairly soft and it made the hole just big enough for them to fit through. I was afraid of cracking it but it was ok.

​@@cyflym11ahh, okay ill definitely try that, thank u so much

Just as long as you're familiar with it, it won't be difficult.

This set is purchased from online shopping in Taiwan. I'm sorry, I'm not sure where else it can be purchased.

Temu has them for about $30

In the assembly package's book, there will be dimensions for the materials. If the size of the wooden boards you measured differs from those in the book, it may indicate defects in the materials. I hope this answer helps you.

Si tu parles du luminaire de bois, effectivement, il manque un trou! J’en ai fait un avec mon petit exacto+colle.

@@jfchevrier15 je parle des petite lumière pour éclairer le libraire book le soir mais le problème il éclaire presque pas donc difficile à voir l'intérieur si je met 2 batterie neuve les lumières clignote sans arrêt et lorsque je met une batterie neuve et l'autre usager sa fonctionne mais éclaire pas beaucoup c'est bizarre

@@carolepaquette6959Je ne suis pas encore rendu là dans le montage… à suivre!

@@carolepaquette6959 mise à jour: je l’ai terminé et sa clignote ici aussi :(. Dommage.

Mise à jour 2: je viens de comprendre qu’il y a un capteur devant la boîte (le truc rond métallique à l’avant). L’idée est que les lumières se ferment après un bout lorsqu’il n’y a pas de mouvement! - Novel Sensor Light: The book nook kit is designed with a sensor LED light. The sensing distance of the body sensor is about 0.5~3 meters, when someone comes near by the book nook, it will automatically turn on the light. Not only can save electricity but also make your bookshelf more special

The materials I received also had the same issue, so I used a tool to enlarge the openings.

We did the same, made the holes bigger with the tip of a file

Thank you, i had the same issue <3

J'ai utilisé de la colle UFO.

@@shuang393 merci

This is a material combination, and the sensor will be included in it.

I'm trying to figure that out right now... Will keep you posted if I figure it out!

And after over 20 minutes of me struggling, my husband pulled the wires through in the first try....

@@bwpianogirlI’ve been trying to fit them for the past 30 minutes any tips ?

The center of the small flower has a hole, and you can thread the electrical wire through that hole. I hope this answers your question.

How did everyone do it? I can't move on because I can't thread the wire through the small flower.

You must connect the positive and negative terminals of the lamp's wires to the wires of the battery box. Connecting the positive and negative copper wires will make the lamp light up. Hope this resolves your issue.

I am honored to have been able to help you.

I also use scissors to cut paper; perhaps the lack of sharpness in your scissors is causing uneven cuts.

eu uso um estilete, coloco sobre um pedaço de madeira e corto com a ajuda de uma régua

I used UFO glue

yes i noticed that too ! 😄😄 i love that you changed it lol im too lazy to

@@MoeShope I get dental pain from such...😜🤣

I just bought this of Temu. I’m making it right now. But I’ve seen it other places

I use AG13 button batteries.

I used UHU glue. www.uhu.com/en/product-page/the-all-purpose-adhesive/63661

@@shuang393 Thanks!❤️