- 40
- 32 866
Hillbilly Handworks
United States
เข้าร่วมเมื่อ 2 เม.ย. 2024
to educate and entertain viewers about the outdoors, firewood, and DIY projects
how to make a echo SCREAM
Showing a time line of turning an echo 440 into a little torque monster. From muffler mod to transfers.
Thanks for watching
Please subscribe
Thanks for watching
Please subscribe
มุมมอง: 144
วีดีโอ
Husqvarna 392xp project saw, first start up and cuts
มุมมอง 5066 หลายเดือนก่อน
sorry for the delay, been pretty busy and needed to do a few things to this saw to get it running. it seems to have decent speed and plenty of torque. thanks for watching please subscribe
Husqvarna 392xp project, finishing reassembly PART 2
มุมมอง 2096 หลายเดือนก่อน
part 2 of reassembling this project saw. there will be a few adjustments being made off camera but other than that I will eventually post a first start up video. thanks for watching please subscribe
Husqvarna 392xp project, finishing up and reassembling PART 1
มุมมอง 1916 หลายเดือนก่อน
I am going over everything I did off camera and started to put it back together to finally finish this crazy build. thanks for watching please subscribe
cutting HAZARDOUS trees, EPIC FAIL!!!
มุมมอง 4356 หลายเดือนก่อน
on a property cutting trees near a house, equipment, and wires. only 2 of the 10 were able to be filmed. the rest were so bad both of us were working on them cutting and pulling them over. thanks for watching please subscribe
falling hazardous white oak
มุมมอง 5K7 หลายเดือนก่อน
falling a hazardous white oak with ported Stihl 461 thanks for watching please subscribe
Husqvarna 392xp project, update on muffler mod and plans for the air filter
มุมมอง 607 หลายเดือนก่อน
finished the muffler and getting very close to putting this beast together. a little more work needs to be done which I will post in the near future. thanks for watching please subscribe
Husqvarna 392xp project, grinding the transfers
มุมมอง 937 หลายเดือนก่อน
now starting to Port the cylinder as we grind out the transfers, showing some "proper" technique to not screw it up. next video will be a update on the porting and muffler mods. thanks for watching please subscribe
Husqvarna 392xp project, UPDATE on fitment of cylinder and piston
มุมมอง 1617 หลายเดือนก่อน
quick update on the 392xp project, the cylinder and piston are completely fitted and now we are starting to take steps into grinding out transfers and porting. thanks for watching please subscribe
Husqvarna 392xp project, fitting the cylinder
มุมมอง 717 หลายเดือนก่อน
now we are fitting the cylinder to the case so it will bolt up and fit just right. I go through most of the process in this video. thanks for watching please subscribe
Husqvarna 392xp, making a plan
มุมมอง 817 หลายเดือนก่อน
now that the cylinder is off, I am planning out how I will be fitting the cylinder and piston to the case and much more. thanks for watching please subscribe
Husqvarna 392xp project saw
มุมมอง 2807 หลายเดือนก่อน
this is an introduction to a new project saw I am doing. it is a clone 372 with a Husqvarna 390xp big bore cylinder assembly. thanks for watching please subscribe
disassembling, porting, and assembling clone 046 PART 3
มุมมอง 257 หลายเดือนก่อน
finishing the reassembly and fixing on testing it out in the future thanks for watching please subscribe
disassembling, porting, and reassembling clone 046 PART 2
มุมมอง 377 หลายเดือนก่อน
part 2 of the holzforma g466 series, starting to reassemble the saw thanks for watching please subscribe
disassembling, porting, and reassembling 046 clone PART 1
มุมมอง 2247 หลายเดือนก่อน
disassembling, porting, and reassembling 046 clone PART 1
holzforma g466 pull rope and handle replacement
มุมมอง 109 หลายเดือนก่อน
holzforma g466 pull rope and handle replacement
ported Stihl 462 vs ported Husqvarna 372
มุมมอง 27210 หลายเดือนก่อน
ported Stihl 462 vs ported Husqvarna 372
Is the mark 1 ported? Sounds like it is
I find the porting can be completely different on same models i have 3 700 and 1 early 7-10. The transfers can be completlely different.
I did one about 6 years ago with the 55mm cylinder using a junk 372 x torq. Swapped in a longer rod, added a cylinder spacer, a 395 carburetor and ground alot more metal out of the transfers. Runs decent, going to try the 57mm kit. Fun little project.
What did you have to do to get the wrist pin to fit the rod?
I find my 700 is stronger but it has 160 compression my 7-10 only has 125. The 7-10 still pulls like a mfer.
Kraljica - king
Good Job 👍
How long before start up been waiting for a video for 3wks since this video?
😮😮😮😮
👍👍🙏🙏
I can’t believe it 😮
Hyway caber piston rings yes sir
Nice job. Tricky looking drop. Stay safe
I regret watching
Ggggggggrrrrrrrrrrrrrrr
😐
Buddy you can take a sentence and turn it into a paragraph just get it done!!
Did you compression test the saw? Reason I ask is if it's like mine compression is fine. My issue is timing. Flywheel is too far advanced causing snaped the ropes and a sore wrist. Better rope and a D hand too but would have been cheaper to retard the timing a couple degrees.
I don't have a compression tester handy but with the modifications I did it helped it out
just to let you know your video is really broken lots of gray screen and skipping when there is picture
th-cam.com/video/ib73ayR9EAM/w-d-xo.htmlsi=gCMCjDLzeEBYiC-A My Channel ...Firewood. 😊
Wooow Power Saw... Nice Video. Greetings from Germany Peter Husqvarna-Pit 😎
Nice Chainsaws Greetings from Germany Peter.
Let her eat David!
Fuck yeah
Fuck yeah
😊 Promo_SM
Well, can they do firewood???? Which saw won ?????
Both can do firewood, the 440 won
Them oldies was stout units
Good Info !!!
I need that wood to make syrup !!!!
Keep the posts coming !!! Saw baby saw !
Good Job !!!
I love you David