วีดีโอ

Why did you remove the coolant hose??

What yr dodge

Wheres the coolant temp sensor?

No lube on the guide pins?

How did you cut it??

GOOD VIDIEO THAT I HAVE A THE SAME CAR FORD FOCUS MK3 DIESEL SAYING CRANKING TIME EXCIDED

Does freeze frame data show the maximum values that occurred? For example, for p0219 over rev code, does it show the lowest rpm required to trigger that code (even if the engine went on to an even higher rpm) or does it show the absolute highest rpm achieved after the code was triggered?

Im getting a p0882 n p0171 code. Battery terminal always corroded, not sure why. Should i buy new terminals to fix the p0882 code?

Anyone else triggered that he left that stone in the O-ring groove?

not one picture of a regulator- just video of how to open the door panel- important part is the door lock component on the top left- why it is still hanging

going to do my tomorrow thanks

Lifting these batteries out are inside

Wow all I watched for was to see how to get this crazy strap on and off and you just skipped over that part. Literally the only unique part of getting this battery out and you brush over it 😅

Y como se reparó la falla??

Are there any gaskets to replace ??

Any cabin air filter that is mounted horizontally will have downward air flow direction.

What did you say it’s called

Thanks for the upload. I’m changing both of the rear controls and trailing arm. Those bolts are rustyyyyyyy! Will definitely be implementing this. I don’t have a torch but I do have an induction heater.

Would be nice if you detailed the torque specs on the thermostat bolt and the outlet bolt ,lots of people goes by torque oem specs.

I changed one on 2016 Maxima , for $60 from Amazon .. didn’t have to unbolt the seat . Took 5 minutes

Am have the same problem and I changed the throttle with Homeuse but still talks about throttle position 1-2 correlation, I need your help

I replace mine now it wont start any idea

thank you

There is no mention of Gaskets on this install I would not want to attempt this procedure without knowing if Gaskets are needed. Especially if it's your only Vehicle.

Other than that liked the video, should have a little screen at the end or beginning of video listing the tools you used. Thanks

Can you please state the sockets that you used, couldn’t understand.

Will this work on a 2016? Driver side?

Hi I have a 2008 Saturn Vue 2.4L ecotec and I believe it's an LE5 engine. I noticed another commenter asked about water found under the dash and on the carpet. I had a somewhat related question. I wanted to clean out my evaporator core with evaporator cleaner but the instructions say to use the evap core/AC condensate drainage hose to do this. I have a service manual that doesn't show where the drainage hose for my engine is located. I saw you told the commenter who found water under the dash to clear out the AC rubber grommet, and that you blow shop air to make the water drain out. My two questions are: 1) where exactly is this rubber grommet located and 2) Is that grommet the evap core drainage opening? If it's not then can you tell me where it is. Much appreciated. BTW I use your video to learn how to do an initial teardown for when i need to change the evap core.

Dont u tighten control arm bolts with upward pressure on arms?

My car is idle In park and my check engine light on I replaced the purge valve about a year. I know air/gas ration is off. Should I replace 1st and could it be possible it will make light come off??

My windshield wiper switch on 1993 toyota corolla won't turn off! Help! Are you near New York & available to fix my wiper switch?

I have the same problem . Does it matter if u purchase the valve from autozone or does it have to be through dealership ?

Do you need to use some sealant?

Where’s part 2?

Horrible advice

That's fine if you have a torch but most people don't, average people have to use map or propane torches.

Shop manual states.. remove the motor.

Why do you need memory saver?

thank you. very detailed and great examples.

are you still doing that chat app?

Thank you sir. Much appreciated

Just wondering, did it work?

Hi is this the 1.0 ecoboost engine.

Where is part 3 where you actually find the cause of the leak?

Very useful video. I have a question. The rust has worked its way and when I've tried to remove the bolt going through the bushing, it broke. I've managed to remove the strut by cutting the soldered nut. Now the bushing is in original place and have the broken bolt part in it. I have to remove the bushing and replace it with a new one. What are my options to remove it? Does a press work or it is better to start using the cisel? What would you recommend?

thanks for this 👍

Thanks for posting this. It worked on my Jeep latitude 2019. Much appreciated

absolutely disgusting - why do people have cars in such deplorable condition?

Hi. Thanks for sharing. I noticed that when you put in the brake pads, at 4:29 and 4:45, you put them in with the clip towards the top, so that when you put the bracket back on, one brake pad has one clip up and the other pad has the clip towards the bottom. Does it matter which way the clips go, up, or down? Or as long as the pads are oriented correctly, brake surface towards the rotor, and curved side towards the front, it doesn’t matter?

I had to go to the part store 3 times explaining what battery I needed. There is zero wiggle room in there the battery has to be the EXACT replacement and terminal post position is important too the wiring is cut to exact length zero wiggle room again.