- 1
- 89 622
KJ
เข้าร่วมเมื่อ 20 ธ.ค. 2022
Fixing And Working On Stuff
How to flush an outboard!! ENGINE "Proper salt removal video"
This Video Shows how to flush The outboard Engine
we Hope This Video Help you if it did
live a Like And Subcribe soon more videos
The following engine procedure are performed by highly trained professionals under expert supervision, plz don't try this at home or do it with your local honda dealer
we Hope This Video Help you if it did
live a Like And Subcribe soon more videos
The following engine procedure are performed by highly trained professionals under expert supervision, plz don't try this at home or do it with your local honda dealer
มุมมอง: 89 652
This is an almost new engine and you are trying to take people for fools
I use muriatic and or marykate hull cleaner phosphoric acid on a clogged Yamaha sail boat motor. Poured down thermostat hole and it foamed up Then flushed out. I try this next . Thank you 👍
Ok guys, I tried it and did it just like you. I never comment on videos, but now I have to say - what you did is really good! My engines are all clean; I checked them. How? I opened the engine to make sure it worked! The engine is as clean as a baby’s bottom! I tested to see if the Exo Lab might have damaged any seals, but everything’s fine. Thanks a lot for your video!
Glad to be off help 😁
I subscribed, these are very good videos thanks. I am going to repower my 26 aluminium fishing boat whether with brand new BF250 Honda or 300 V8 Mercury XL CMS, hard to decide. What is your feedback on the 250 Honda, thanks.
👍🏻🇨🇦
Does poppet valve need removing?
Nope just like they did its good
Never saw the shift shaft disconnected or mentioned. Please folks, do not follow this video for advice.
You do not disconnect the shift shaft on a Honda, it slides right out. Great video!
If you dont understand that the shift shaft stays with the lower unit dont Comment on videos without getting good information about the engine!
I love it when I learn something I need to know!
We are glad to help you 😁
Excuse moi je ne parle pas anglais mais une fois fini le rinçage comme dans la vidéo en obtenie le même résultat comme sur la photo du début de la vidéo
You dont get the same result try it yourself
great video , attention to removing the thermostats noted so entire water jacket gets treated.
Correct 😁
bravo dečki
Great video! I am planning to do this job and you fellas have made it easy for me!
We are glad that this video helped you
Ma brate ubili ste ga svaka van dala😊😂
😂Hvala
Great job guys 👏
Thank you 😁
Thanks for share, how many GHP or Liters per minute has the water pump you are using?
grease the spline and you won't have to hit it so much to get the lower unit to drop
Thanks for the tip,Will do next time😃
I hear just hot water. None of the cleaner works.??? 😮
Hot water works only after one use.Chemicals work very well actually try it...
Excellent, thank you.
Thanks 😃
well done
Thanks!!
“Me, my friend and I” lol you guys honestly speak damn good English.
😂😂😂 we are trying..
Nicee!!
Thanks
Thanks for watching if you want us to make more videos SUBSCRIBE!!
Very well done gentlemen! English is not your 1st language, however you have made a very good video in English congratulations! I was worried when you took off that trim fin to access the last bolt holding on the lower unit in that you did not mark or index its position. But at the end you showed that the proper location for that trim was already marked by the manufacturer. and you are correct about always lubricating hardware in marine applications. Thank you!
Thanks!! Its hard for us to explain in english..We tryed our best,Thank you for a nice comment and nice compliment we gonna post more vides and try to explain it even better...
This method does work, I've done it using Rydlyme on an old saltwater motor. It can be rough on the anodes so replace them too if you can.
Yes it works with other Chemical solutionsalso.. But you choose whats best for you...Tnx for commenting
@@Ki_jo can this work with hydrochloric acid<?
@@makingcookingfixing Personally i wont try it...Maybe its to hars on internal anodes..
@@Ki_jo thoughts on this wearing out rubber gaskets like the head gasket etc
@@wazup3333 Nice tought but i know guys that are certified honda dealer that are doing this for long time they had no problems..Neither did i im using it for 3 years now
Good morning what rinse aid do you use? Thank you for your reply
Lime a Way Extra green Bottle From ECOLAB ..No worrys thanks for your question.