วีดีโอ

Clara what if we are cutting a piece with 100 or more hole in it? We don't want to use centralized piercing but we do want to move the cutting process around the part strategically so that the part doesn't get too hot in any one area. How do we do that? We have a Morn 6000watt with cypcut software

Hi Clara, the power of my Raycus 3kw machine suddenly change decrease during cutting and i have to decrease the cutting speed. Randomly it increase to normal and decrease. I can notice this from power consumption which is written in stabilizer. I have checked every thing but nothing i found. what should i Do?

hello clara my raycus 1500w showing alarm Raycus laser err1 how to fix it please explain

I have a 3000W fiber laser cutting machine and when cutting 8mm or above the lens get black points very fast.. like 5-10 minutes cutting time.. I already tried many different pierce strategies but no success.

Hey Clara . I have a 3kw fiber laser . Would you recommend cutting copper bus bar . Can you provide me with basic parameters . Love your videos

Hello Clara, I want to check out your shop, but the address is not safe enough. Hackers may spy on our communication. It does not support HTTPS and so my browser does not give me acces to your web site. Please upgrade to HTTPS and I will visit again.

hello mam x axis limit- alarm is coming how to solve it

Hi Clara may I know how to solve Alram 72 and 68 x servo alarm and x solf limit +

Hi Clara. Good videos. They influenced me to purchase a 3kw Maxphotonics source to replace an IPG unit. I got the laser to fire, it cuts 1 hole and cannot cut additional holes. Also, nozzle gets very hot. I used same configuration from my 2kw to try to cut too.

Need that pdf mam. For 6kw

My laser protective lens get burnt frequently

Alarm Ethercat: Timeout Err. check connect

Hello Clara, When I try to use the corner technique I cannot change the power as the "laser is in communication mode' how do I fix this

What problems do protective lenses cause when cutting mild steel, that make us suspect that one of them is damaged?

ty clara

In my laser the shutter does not turn off and it does not signal any alarm, only in the resurfacing device the alarm button turns on

Hi Clara, glad to see this video I have a problem, my Raycus 3000 watt machine has a problem with the red light If you want to cut the second plate, the red light doesn't come on, what's the cause and what's the solution? thanks

Hi there we have hanli 6000 and it’s shows E11 error. We are not able to fix this. Please help us

hi Clara, i have my new machine set up from China, I am very new about laser cnc with cypcut, my problem is on the remote if i pressed Z down, the alarm stated: Jog close to plate even though there was no steel plate on the table.

ty laddy for this training cource <3

Hi Clara What are the names of the aiming pins in Max Photonic? Thanks

Hii I have a 6000kw laser cutting and I have a 16bar compressor connected to the machine. When I cut 5mm carbon steel it cuts well but when it’s small holes it leaves slag , what can I do to fix this?😀🙏 7 it’s the maximum speed I can cut 5mm My power and duty are 100% And focus on -4, What air pressure do you recommend?

Thank you clara . Video is very helpful ☺️

Preciso de ajuda sua não estamos conseguindo cortar chapa grossa acima de 4 mm Se puder me ajudar 12 mm é 19mm Raycos Raytool 3000w

I have 3kw. Raycus and raytools bm111. We have problem with the upper protective lens. When I checked the upper protection lens during the 30-minute cut 10mm, there were about 5 burns. These burns were on the upper side of the lenses. And also it occurs white dots on the lower protective lens. Firstly, I have to fix the upper one. What am I going to do? Thank you so much for all those videos.

Muchas gracias Clara ! Fabuloso tu canal. Qué bueno contar contigo para ayudas en temas de láser ! Éxitos !!

Hi.iam tara from kuwait.i have problem.madam.so please suggestion me.-alram.z axis is not worktable range

i have a problem with the nest, if the sheet is too small and the parts in the nest are many, the function will misbehave, hoe do i know that the elected parts will fit on the available sheet to avoid the error??

When etching or engraving is it possibe to cut in both directions and not just one way?