วีดีโอ

😊😅😅😅😂😂😂😂

No shit!!! That the most basic of all the knowledge of any vehicle🤦‍♀️ Push the accelerator pedal to go faster 🤪 Or the long skinny one on the right for all you dumb dumbs out there that don’t know how to drive ANY vehicle. Really!!!! Are you sure 😲

Omg really???? You are a “genius”

Thank you so much. I tried the downhill technique and it worked great. Now if I can just find a way to go downhill Everywhere I Go

😂 😂 😂 😂 😂 😂

you must be a bit stupid?

Smartass! Freakin hilarious! 🤣🤣🤣 Love it man.

That's one way to be ignorant.

Lol

Funny,u got me

Hi: I’m in Greece and my JK side marker lights are also blinkers from the factory. I guess this is for the Euro spec JKs. My question is how can I make my turn signal to work also as a marker when my parking lights are on?

LMAO....AWESOME!!!

Omg thanks soooooo much!!!! You’re the goat!

thumbs down waste of fucking time, get a life bud

Just to keep everyone informed, I just did this to my 2016 Willy's and there are no problems at all. The Clips are a real pain unless you pull the red locking tab all the way out. It took longer to get the tape off than to do the mod itself. Excellent job Tommy Wise and thank you

I did this on my 2018 jku 4dr sport. I can confirm that it works the same way as the video. Plus that I swapped out the bulbs with non polarized 168 led bulbs and they work just the same. (Just make sure they are short enough) No resistors needed because there is no hyperflashing. Can't say if it will work with those flower aftermarket replacements but should. Apparently the two wire method is superior to the one wire in more ways than one. Great going bro!

Hi Tommy. Can you achieve this same thing with the Trail Rated Badge lights (from Badge Glow dot com?) I just bought two badge glow lights (I have badges on both sides) and I'd like them to do exactly what you have done here with the fender markers. Thoughts?

Lol boi

Brilliant!

OMG, that's funny AF

I just did this on my 2017 Jeep Wrangler. Works and it took me about 30-minutes. Very happy with the look. Awesome instructions. Very easy to follow! Thanks for this!

Great video and thanks for the info.

I just did this mod and matched the white green to the white/yellow and the black to the white/red wire. The side mark blinks are synched with the actual blinker blinks. I just shaved off the plastic around the wires so I didn't have to cut two of them. Wrapped with electrical tape, works perfectly. Thanks Tommy!

thanks for wasting my time

With a aftermarket Led lights it blinks in tandem with front marker lights when the headlights are off but if you turn on the head lights only the fender lights blink and the front ones doesnt.

Thank You so much for this informative video! I never understood why the Side Marker was never a blinker from the Factory. I just did this Mod and also replaced the Side a Marker Bulb with a LED Bulb for even brighter light output.

that was great!

Which color is blinker which is ground and which is positive ?!?! Can anyone help before I start cutting?

Looks like a great setup! Does the mirror have vibration at certain speeds?

You funny

Just did this on my '17 and it worked great! I used wire splicers so I didn't need to cut any wires, just disconnected the plug for the side markers and jumped the wires to the turn signals. Thanks for the great video!

I used these all summer and they worked great, be careful to not scratch the paint while screwing in the mirrors though, it does shake while on the freeway but still works fine

Thanks for the great info. Just did this today on my 2014 JK Unlimited Rubicon. It worked fine, but DON'T USE THE CRIMP-TYPE CLIPS on the wires. Instead, SOLDER SOLDER SOLDER! These are connections that are exposed to the elements. Crimp clips may not be terribly reliable (e.g. may get corrosion, or if water pushes the wires at a funny angle or they get stressed for example when disconnecting the front marker lights to remove the grill) they may lose connection, and from a safety perspective the last thing you want is to have some of your lights not working. Even if taped up nicely when using crimps, moving the wires could cause a connection failure. This is not the case if you solder the connections, which is vastly more reliable.

Did this modification yesterday on my 2012 Ruby and it worked great. Took off the grill for easier access. One note to whomever does this, I left about an inch of wire on the plug that goes to harness coming off side marker which left me shorter wires when spliced them to the turn signal wires. This made a tight fit when I reinstalled both turn signal and side marker light into their housing. Everything worked great but I may splice some wire extensions to the side marker wires next time i have to change the bulbs or try and re-route them so they wont be so tight. Other than that doing this Mod I feel safer letting on coming traffic know when I am turning, especially in the city traffic. Thanks for the awesome demo, made this easy....

I tried this on a 2015 jk sport and the side marker won't work when the lights are on but works as a turn signal if the lights are off. Any ideas?

I didn't have a kid , I broke my windshield :(

Thanks for the video, everything work out great, as an added bonus, the original side marker connection makes the perfect tie-in for led running lights under the running boards.

1 wire method works exactly the same as the 2 wire method . you are just doing more work . if the 1 wire method does not work it I because you wired it wrong .

I'm dieing!! I love it though!!

Lol lol Hahahaha. My man.

i laughed so hard at this lol

Why does this not have more views? Haha

Great JK mod! Thanks for doing the homework for the rest of us.

I'm gonna try this today thanks!

Tommy, on the side marker/turn signal mod, do the hazards blink as well?

I could not contain my laughter.

Thanks man did this works great

anybody done this on a 2014 wrangler 2 doors sport? I want to know if this would workr on mine

Does this work w/ aftermarket lights?

Just did this on a '14 jku and worked as advertised. Also tried switching wires around and it did not matter