วีดีโอ

@@LiyasatAli-sv4mj 💪👍👍👍

@@BoshliqEngkattasi of course I think so too )

thanks for your comment! You are absolutely right that working with electricity requires maximum safety. We use a waterproof cable, and the cable is needed to protect against mechanical damage and UV radiation. this will provide protection against possible accidents and increase the reliability of the system. Safety always comes first!

@@MCtoJa I don't think so, as the metal is deformed and will look about the same after leveling, if not worse

👍

Falou tudo

@@reynaldomatose 😂

@@adhanomabedgebray5874 The gas temperature sensor did not work in it!

@@ГрэмГрин-я6й This is a 16 kW air conditioner, it had a faulty gas temperature sensor.

@KlimatCoolUa понял, сталкивался с подобным на мультике, но там до обмерзания не дошло бы - Дайкин, просто автоматика всё отключает. Просто с пульта самодиагностику запустил, и всё ясно - поменять датчик давления.

@@ГрэмГрин-я6й it would be good if self-diagnosis was in all air conditioners ))))

@KlimatCoolUa согласен, было бы гораздо быстрее и проще для тех, кто понимает. В том моём случае до меня пришла другая компания, и они прямо официально бумажку выдали, что неисправен компрессор, и необходимо либо заменить компрессор, либо всю систему. Но это уже другая история))) забавная)

@@יוסירוזן-ס7ת vacuuming was done, it just didn't make it to the video, because the video is about how the installation is connected.

@@יוסירוזן-ס7ת if the video does not show how we connected the internal unit of the air conditioner! it does not mean that we did not mount it !

@@mw5644 everything works great with us even without torque wrenches 😉

yes yorks were indeed popular and reliable air conditioners! Even now, some models work without problems, despite their age. They were real "workhorses". Thanks for the comment! ))))

now the company manufactures high-quality heat pumps

@@KlimatCoolUa согласен, именно рабочие лошадки - все поломки в основном касаются износа пластика или вентиляторов по срокам эксплуатации, а основной функционал был исправен, и компрессора, и теплообменники...

@@KlimatCoolUa про тепловые насосы не знаю, живу в климате до минус 40, поэтому раз рискнул для заказчика, взял ему Vetero, кстати, завода Gree. Пока пару лет без претензий.

@@ГрэмГрин-я6й yes, indeed, with a good tool the work goes much faster! Saving time and effort is always nice, especially when the result is of high quality

The pump together with the float. A set from ASPEN Pumps. I liked it too👍

glad you noticed! Can you show me how to do it better?

I overdid it a little (did not calculate the thickness of the wall 😔

@KlimatCoolUa да это понятно, не всегда удается в силу тех или иных причин, когда поспешил, когда чисто физически невозможно всё предусмотреть... Мы раз поторопились, не заметили разницу в длине стен, думая, что за стеной балкон, и вышли из угла зала по диагонали не на улицу, а на кухню, так как была лоджия, и кухня была длиннее зала на глубину лоджии. Вот это был анекдот )))

@ГрэмГрин-я6й I also had a similar story, they made a hole at an angle, somewhere they made a mistake in the calculations and came out in the bathroom and not on the street )

@KlimatCoolUa в таких случаях обычно всё решает кабель-канал, словно так и было задумано))) если это возможно, конечно)

@@ГрэмГрин-я6й yes, that's right. In my case, I was lucky that there was a white tile and not much came out of it, the banal white silicone helped me )

👋

@@Daniel-fs5npYes, I also like them more, but lately the float has been leaking in the rubber band area, very often

and my cap is mitsubishi 😂😂😂

what did you do first?🧐

😂

@@jackwells1035 GREE NICE! 👍👌

@@lamnguyen4709 To connect the water pump to the air conditioner: 1. Connect the air conditioner drain hose to the pump inlet. 2. Connect the pump outlet to the drain system. 3. Connect the power supply to the pump according to the instructions. 4. make sure the pump activates correctly when filling the drain tray. follow the manufacturer's instructions !

🧐

@@Олександр-р6ь6т this tile will be dismantled and a new one laid!

👍👍👍

@@ГрэмГрин-я6й on the right side, a hole is made under the foam, I just cut out this moment, because during installation this moment looked very bad) thank you for being so considerate 😉

@KlimatCoolUa 👍

✌️

Thanks You!

@@illia5650👋, I liked it too !

​@@KlimatCoolUa❤❤❤❤

Yeees )))))

😂😂😂😂

Thanks

@@Alex_25russ if you work for a certain time and learn, then for sure, but when you take it in your hands for the first time, it is not completely clear)

it is better to use a screwdriver and not tear off the thread ☝️

💪😎

@@logistics.a.1546 in specialized air conditioning and ventilation stores ( HVAC ) , manufacturer of agp .

How do you know how I store my tools ?

@KlimatCoolUa это следует из содержания видеоролика.

@@dougaustintx this is done at the request of the client, the client has been warned about all the risks !

​. Ah, roger that!

@@Puffalupagus360 I use a flaring tool Value, or Diamond Black

@@Inst05 these are such brackets that are not attached to the floor, they do not require fastening, because they are attached to rubber rings

又没有振动，不用固定

@@yuhanzhang2795 Yes !)

@@공공구-p8v first I want to see a video on your channel

look closely! this is not a marker, these are factory slots in the metal!

😎✌️

Thanks