- 16
- 202 074
Cars cars cars
เข้าร่วมเมื่อ 18 พ.ค. 2017
When your phone display is DEAD but you have to finish the Porsche ECU job...
I was working on Porsche Panamera ECU with P0556 DTC but accidentally dropped my phone and display went all black, with only half of it reacting to finger touch. But I still had to run last diagnostic checks on the ECU after the repairs, so it was time to get creative :)
มุมมอง: 497
วีดีโอ
Ford Focus / Fiesta / S-Max / Mondeo remote key fob manual programming. How to add remote
มุมมอง 70K4 ปีที่แล้ว
This programming procedure works for Ford Focus 2, S-Max, C-Max, Mondeo 3, Fiesta. You can manually program a new remote to your car without having to visit a dealer. Here is how to do it: - insert a key and turn it 4 times from position 1 to pos. 2 and back to pos. 1. A long beep will sound, the car now is in remote programming mode. - Turn any button on your new fob or flip key. Another long ...
How to remove stereo on Nissan Juke - quick guide for car audio DIY enthusiasts.
มุมมอง 2.2K4 ปีที่แล้ว
This is a simple tutorial of Nissan Juke audio / radio unit removal.
Mazda 2 remote flip key programming with KD-X2
มุมมอง 12K4 ปีที่แล้ว
Programming a remote key / remote fob to Mazda can be done manually. Here is the procedure: - Get inside the car, manually lock doors - Unlock and open driver's door - Cycle ignition 3 times ON-OFF, leaving it in OFF position - Close and open driver's door 3 times, leaving it open at the end. Door locks will cycle, the car is in remote programming mode now. - Press Unlock, then lock on your new...
BMW F series smart key with display
มุมมอง 1.3K4 ปีที่แล้ว
A short review of the functions available in Smart Display key for #BMW F series
Ford Fiesta broken ABS module removal and disassembling for repair if you have error code U3000
มุมมอง 78K4 ปีที่แล้ว
The process of removing and disassembling ABS module from Ford Fiesta 08-15 with DTC (error code) U3000. 2 ways are shown, you can remove the whole module for replacement or just the electronic part of ABS so you can still drive the car while your ABS is being repaired. Yes, instead of spending $800 on new ABS module you car send the old one to us for repairs and we fix it! กระบวนการการถอดและแย...
Ford Ranger 3.2 TDCI chip tuning
มุมมอง 3.2K5 ปีที่แล้ว
PCMflash was used to unlock and remap the ECU, the entire procedure from taking the ECU out to final assembly and car start was pictured.
Nissan Almera key programming with KD X2 and mobile phone
มุมมอง 2.8K6 ปีที่แล้ว
Nissan Almera N17 key programmed using KD-X2 tool.
KD X2 + King Chip - does not work.
มุมมอง 1.4K6 ปีที่แล้ว
Tried to generate various ID chips using KD-X2 with JMD King chip. Seems like KD-X2 doesn't work with these.
Toyota Hilux/Revo/Fortuner 2.4 acceleration after tuning
มุมมอง 3.6K6 ปีที่แล้ว
Toyota Fortuner 2.4L D4D 150 HP engine was chip tuned to 185 HP by me. If you are interested in comparation with Mitsubishi Pajero Sport them Pajero Spoort acceleration video can be found here - th-cam.com/video/s8e_F-4a5Mw/w-d-xo.html
Mitsubishi Pajero Sport acceleration before and after chip tuning
มุมมอง 2.3K6 ปีที่แล้ว
Dynamics change of Mitsubishi Pajero before and after chip tuning are shown. ECU was remapped with custom made tuning file. If you're interested in comparation with Toyota Fortuner you can find a video with Toyota Fortuner acceleration before and after chip tuning here - th-cam.com/video/B_ oVnvJY0/w-d-xo.html Mitsubishi Pajero Sport 2.5L turbo diesel Gain 45HP, 55Nm. Measured by Drag-On
Ford Mondeo / S-Max odometer correction
มุมมอง 16K6 ปีที่แล้ว
Correcting mileage on Ford Smax / Mondeo car dashboard after instrument cluster change using Iprog script via OBD2. Коррекция пробега на одометре Форд Мондео / S-max при помощи Iprog или IprogPro.
Chip tuning BMW 320d F30 ECU Bosch EDC17C50
มุมมอง 4.2K6 ปีที่แล้ว
Engine ECU is remapped, adding ~35HP and ~50nm of torque (so-called Stage 1 tuning). The car software is also recoded/reflashed with full option package (Sport settings, steering/suspension adjustments, digital speedometer etc)
Mazda 2 dashboard mileage adjustment with X300Pro3
มุมมอง 4.7K7 ปีที่แล้ว
Mazda 2 dashboard mileage adjustment with X300Pro3
I dint have an error code but the check valve seems to be stuck the brakes wont unlock
Who's the music by
I just bought used mazda2 ts2 2009. But dealer give me basic key like motorbike key. I don't have fob. if I buy it online than can I program it like that? will it cause any problem in future?
Bro do you have a solution. Pls tell
Lose the crappy music.
Thank you thank you thank you 👍🙏
I have a doubt, I have a 2011 Ford fiesta and the front right caliper is stuck, but there arent any code, just the brake the caliper stuck, what it could be? Maybe bad caliper or one valve inside of the abs is stuck...
Great..just fixed my key in proper quick time,in fact it took less time than the length of the tutorial..good work but could be made better without the abrasive/annoying background music!
I change brek fuild, after 1 weeks ABS alarm, the car cannot auto brek at incline position
Hi, i got abs, esp and engine light. Got diagnostic check and it says left front abs sensor. I changed that one and wheel bearing but still have the same problem and same fault. Can it be the abs module i need to replace?
I am having the same situation with my Rear Left abs sensor, how it's going for you have you fix it?
Hi my friend . I have got a working tested part, complete part from ford UK same serial numbers etc. I took it to a garage in Thailand, pattaya , that just plugged in and said, it's no good , bad code, I believe they did nothing. I took it all back. ( I saw the part tested in the UK, taken from a vehicle with no codes) Anyway, could the error codes be eradicated by replacing the electric module only ?? I have no facility other than a Ford garage to bleed brakes and pump. Thank you Many blessings happy songkran
How much its cost in MALAYSIA CURRENCY?.
Hi I need more help ao I have done what you have shown on video & my key still won't work any suggestions thanks
What about the chip. I've did it and the remote works but won't start the car
sir after replacing engine mount, wheel sensors, brake pad, rubber cap of ford fiesta 2011, all wheels got sticked, what is the cause ABS Module?
ขอบคุณค่ะน้า กำลังจะไปทำเกือบเสียตังแล้ว 🙏🙏🙏🙏🙏
That stupidly loud pointless music, I searched for another video instead.
Same here.
@@user-vh1ol1sm6elol why show so much hate bro acting like you didn’t reply to yourself
Tried the Flipper zero gadget on my car, managed to open door with it but locking failed. After this experiment, car's key stopped working, couldn't unlock/lock doors, but the sync helped.
Lol. I liked the production values 👍
Gucci brand it is for poor people to look like rich.. umm Gucci.
What bollocks. Doesn’t even work. Ffs.
Thats intense
what do you recommend for transporter t4 1998 model digital part
thanks so much for this - I had replaced battery as key fob not working - still didnt work so rang local Ford dealer who wanted £75 just to look at fob - fortunately I didn't go to them ! I didn't realise key fob had to be reprogrammed. I also looked at another video which instructed to turn key between II and III - that didn't work, but it did work when I turned between I and II as instructed in your video - it didn't work first time but it did work when I clicked button twice [not just once] after doing the I to II thing 4 times.
Thanks worked perfect 👌
Hi mate do u have to bleed break after
Do u have to bleed break after
@@marklewis2517 yes
Loc po sk mgkano pagawa tnx
This might help someone👍 2009 Ford S-Max 3 Button Key Fob Step to program key: - Insert key into ignition - Turn key 4 times between position 0(Ignition OFF) to position II(Ignition ON, without starting the engine) - Key off ignition - Press any button on remote key fob(hazard lights(indicators) must flash) - Wait 20 seconds or put key back into ignition and turn to position II( Ignition ON) ⚠️THESE STEPS ABOVE MUST BE DONE WITHIN 3 SECONDS⚠️ If you have more than one key to program just use one key to enter the programming mode and when required to press the key fob button, just press one button on each remote and that’s… GOOD LUCK
When you reinstall the module. Do you need to bleeding the brake oil and add oil? Or it is just plug n play?
Yes, you need access to either Ford IDS i.e. a Ford dealer or Forscan on a Windows device, so you can use the 'ABS bleed" functionality. The traditional method of bleeding the brakes won't work because it won't include the mechanical area of the ABS module that are now full of air. The 'ABS bleed' functionality opens each section in turn i.e. a caliper at a time, and pumps brake fluid through to push out any trapped air.
Hallo ..you have module abs ford fiesta 2011 sir..second and function
Part number?
@@carscarscars186 AV59-2C405-EA A426G GERMANY At 10.0212-0728.4
@@carscarscars186 I share on your Instagram sir..
Hey I need a link to purchase this key.
Great video, I would like to do the same as I will swich to convers+. So I need only this program and Elm327 cable?
LOL you need an IprogPro programmer first (~$1000), then a Ford OBD script for it (~$100), then an OBD cable for Iprog ($40). Enjoy :)
Hello, if I buy a remote with an empty unrecorded chip for Mazda 2, will it be possible to program it in this way and it and the car to start with both keys?
Sure, if you have the tools.
@@carscarscars186 what kind of tools ?!
Hi I have a 2011 fiesta and have the same problem, i got it checked by a mechanic and advised either i spend a lot of money for a new abs module or just leave the problem and just to drive carefully since abs is not working anymore. My question is, if I leave the problem would it cause any harm to the vehicle?
Good information but why all the drama ! And music i just dont get that bit its just not needed
very anoying music why???????????????
Hey, when you remove the electronic unit from the assembly and keep the hydraulic unit installed in the vehicle, will the vehicle have normal mechanical/hydraulic braking? Is the vehicle drivable?
It usually is. I used to drive my own car like that for few weeks LOL
@@carscarscars186after that u reinstall the electronic?.
@@carscarscars186after that u reinstall the electronic?.
The theme was 👌🏽
Hello sir, I've got a 2016 ford fiesta sports(push start). I have 3 lights on my dash one of them is the abs,traction control and the brake light on. I was wondering if you could give me advice on which parts of the car could be causing this problem. I don't have a scanner tool to reset the codes. Do you think this could me a bad abs module? It would me a lot to me if you respond to my message. Thanks in advance!
The only advice I can give you is visit a Ford specialized garage (or a dealer) and ask them to run diagnostics on your car. It can be anything from blown fuse to abs sensor to abs module itself.
@@carscarscars186 firstly thanks for responding. I am planning on taking this to the dealership but i don't feel safe driving the car for 10 hours in the condition that it's in. I live quite far from the capital. You've mentioned something about being able to drive the car without the abs sensor. If i were to remove it while i wait for the parts or maybe ship you the abs sensor would this be safe to drive? And does removing the abs sensor get it of the acceleration lag for the time being? And i apologize if i am naming the parts wrong. I'm currently in the Philippines on vacation but i normally live in the states where good me mechanics/shops are only a stone throw away. Thanks again
@@keepitsimplesilly3212hi, did you find out what was the problem?
Focus mk2 does not work. Any tips? Cant get to the beep sound .. 4x nothing..8x nothing. Thanks
hi luka did you manage to resolve this issue ? , i ask as i have the same problem . tried every instruction , they just vary in how many key turns really . i get no beep at all and both fobs do nothing at all . so just wondering if you have found a solution .
@@fobrien1 hi nothing since that. I have tried a couple of times but always nothing. I gave up on it already. If you find a solution or some tip please let me know. Thanks
hi luka thanks for your reply . i have tried ford sites , but i either found nothing of any help or i asked and received no help . if some info was available it would help us or might help us to trouble shoot and rule out or rule in what the issue might be . but having looked a lot i found zero . for example if i knew the car should still go into program mode and beep even if the remote locking system unit was not working ,well that would help . but i found nothing of help . so the only solution i guess is to try and troubleshoot it , and possibly get my mechanic on to it . because you can get wear and tear / damage to the key requiring new keys . that can be expensive . but thanks for your reply .
My Ford Fiesta 2011 had a trouble code U0423 for a months ago. I didn't give an attention for it since the car is running normal condition. Recently, I noticed the brake in the front left was sticking up. The fluid pressure won't release even I released the brake pedal. I checked already the piston on the caliper and fluid lines but everything seems fine. My question is. is it possible that the ABS ECU was the cause of sticking up the brakes on front left?
It is more than likely.
@@carscarscars186do any belts have to removed when replacing module on 2014 ford fiesta ?
Goood
Is not the same juke
Can you unlock the doors if you forget the keys inside ?
Call someone who has the other key and have them send the frequency from their key fob over the phone.
I have seen brake pedal switch can cause same issues. Is this correct?
Not quite. Broken switch can make your shift lever stuck in P position, but will not cause U3000.
@@carscarscars186 thankyou, our car drives normally but has these lights, at first intermittent, now on all the time...obd2 elm 237 no codes detected, no matter the app. Any ideas or is it ultimately the module?
@@seekkkkkkkkk7366 ELM327 won't help you. Why do you think we use expensive professional equipment and not a $5 butt plug LOL Take it to any decent garage or to a dealer and ask to scan ABS for errors, then let me know the codes.
@@carscarscars186 ok Where in thailand are you please May need to see you ,👍 we are in thailand pattaya
@@carscarscars186 where u based in thailand.
Pure pish...another crap video with info that doesn't work...and equally crap accompanying music
Thank you so much man, that was big help
4:40 where did you get the fob on the left? Is it original?
No it's not original. Your local locksmiths should have them in stock.
@@carscarscars186 Hello, if I buy a remote with an empty unrecorded chip for Mazda 2, will it be possible to program it in this way and it and the car to start with both keys?
Do you repair the module yourself? If yes, how could I conatct you please?
Yes I do, contacts on the intro screen.
#bengkeltomoprobolinggo present
Do you also repair leaks from the ABS pipes?
Never seen such a thing.