วีดีโอ

thank you for this detailed vid my friend, did it by your steps and my makita is 💯

Awesome video! I just took mine apart with ease thanks to you, but I still don't know what is wrong with it. So randomly, it just stopped working, period. It was not droped or wet, and it's very well taken care of. It even looks new. But over 4 years old, so it's way past warranty. So, when you put any battery on it and hit the switch, the light flashes quickly once, but the motor won't run and doesn't even make a noise, nothing but a quick flash. If you keep hitting the switch, the light will keep flashing once, but nothing else, almost as if the safety feature to not rip your wrist from your arm when the bit gets caught on something is stuck... please help as I called a dewalt repair center, and they are literally charging me the price of a new one.

Milwaukee should have a recall on the switches, clearly an ongoing issue with a sub standard part at manufacturing,

And just a tip for you there is absolutely nothing wrong with those wires clean out the switch and that will work perfect

Did you honestly not notice that the Anvil wasn't turning go back and check it and you will see

Can I ask as to what spot welder you are using? I have not gotten a chance to review your other videos YET... so I apologize if this question has already been addressed.

New to your channel. How thick are the Nickel pieces you are using here?

Good work!

Cấu tạo bên trong cụm búa không hề giống dch273 của tôi

Thanks man, i think my switch might have dirty traces too. It gets power up to the switch but no power out, continuity on both legs to the motor, i get a flicker of power to the LEDs when i pull the trigger but no motor action. Going to pop the switch apart tomorrow and clean the traces and let you know if it works. I appreciate the content. I was about to buy a replacement awitch until i found this video, ill give a go before buying a new switch.

Why my tool protect with 24v accu. Can I remove the protection

@Mack_Dingo This is a tungsten sharpener for TIG welding

What is this? like a powered knife sharpener?

Great job, sir.

.

Hi! Nice content 😉 What kind of grease do you use?

Worked great. Quick and easy. Thanks

Thanks

Hi mate, where do I buy the controller part for the dtw 1002?

nice Schlapfen

I tried this on my XC 6.0, no change after 10 minutes. Am I safe to leave it for an extended period? The 6.0 is at 3/4 bars, I’m using my 3.0 at 4 bars

Easy repair. Go for it

Наковальню любой школьник заменить может. Ты блок электроники к жизни верни!

I'm guessing this is from the Russian tool repair manual?

No oe hechastes grasa dieléctrica¿?🤔 Saludos

TheBil

Saved me $$ and time thank you

I have like 4 dead M12 batteries I'm gonna try this on

0:45 I don’t speak chipmunk on helium

I think we need to review the definition of easy

welding master

What if I can’t tighten the Chuck to put an Alan key in there?

Caution, on some models I've had associates destroy the mode selector mechanism by using the impact driver to remove the chuck. There is usually a relative thin plate in the selection assembly that controls the shift between torque, drill and hammer, the impact driver has enough strength that it can bend or warp that mode selection plate, mode selection no longer works correctly and the torque settings are wrong. It can be corrected but it requires the gearbox to be torn down and rebuilt which is significant.

Did it fix the problem?

Today had a job to do with one of these and found the blade stuck tight and unable to swap. Couldn't remember if it was a reverse thread or not and didn't want to tighten it by mistake. Couldn't find out from any of the online manuals. You answered the question first 2 seconds of the video. Thanks!

Unfortunately owned by China 🇨🇳

The electric brake feature is problematic with these saw switches .bad design.

I'd say it's not a good repair. It will work. For some time. Mixing worn cells with new ones in a series connection is not a good idea - cells will wear differently. Good pack of series (SxPx) should be picked from same cells, preferably from same lot and even then checked for internal impedance. Especially for high power loads.

Thanks for the repair 👍

Good vid buddy. Haven’t watched fully yet but I was coring a whole with this drill and the core got stuck in the wall and the chuck couldn’t be reached. So I had to shake the drill violently to get it loose, and it bent the chuck slightly. Will this video teach me how to replace the chuck?

👍

Mines has burned varistor nd i cant tell what part num there are because it completed burned can u tell me the park num of it on urs?

Hello. Thanks for your video. Dear friend can you please put more light it's too dark .Thanks

it would be great, if you could share more details about the programmer and where to get it.

Hello can you share the tool used to unlock the BMS

What was the fix, did you replace something or just clean it and apply new grease. Maybe I missed something.

I'm starting a tool repair biz,,,hell no can't assemble that mess without a parts diagram, because? I didn't tear it down!

Hola, quise hacer lo mismo, pero vino distinto, como muestras en tu vídeo, será por el año 2023 q actualizaron? y no se como destaparlo y darle mantenimiento al switch. Espero puedas ayudarme con saludos desde Perú 👍

What are you spraying on the switch? I'm trying to fix some drills that had brushes ran down to nothing, but after replacing them,,& new plug-in? Nothing when I push the trigger😡

Really helpful! Be careful with the inset of the bearings and check that you hammer on the correct race. 😊