วีดีโอ

Was there a reason you didn't use the other Freeze plug port that appeared to be more accessible?

Is it the same for the back

Did you have to drain the transmission fluid beforehand? In this video he mentioned it. th-cam.com/video/6QS4Eyo0VIY/w-d-xo.html

Thank you so much. You got off easy the dealership wanted 180 dollars an hour to swap mine. Thank you again😊

Most filters require 3/4 to 1 turn.

This is cake. Try the first gen Fusion wheel bearings- they’re press in. These ones a toddler could do in an hour.

Appreciate the walk through. Pretty sure I somehow stressed the axle and damaged the drivers side axle seal while replacing the shocks.

Thank you!

106 in lbs for the plugs from the maintenance manual.

Wow! had the same problem with our car. Wife brought it into Lincoln place for oil change and got the same song and dance and I was like BS, $150, nah, bring it home then find out on TH-cam it's a common problem. Gee thanx Ford! 🤑🤑 another fine product!🤪🤪 Thanx for the video, confirmed what I thought.

Thanks dude!

Will this work for a f350 2018 as well??

Got 2 of them one is 12ft other is 16ft. Both have a hydraulic jack

Harga baru nya berapa ini seri berapa

I just did the hub ion my 2013 mks , 94k mi , and the rotor was held on by one allen flush hed bolt with I might add had lock tight on it , never been off before , if I didn't own a set of torches , I would have never have broke the bond of the lock tight , after that it was just as the video described / Frank

Cool well done!

Nice video 👍

No cam lock at the top is very bad. If you try and spread gravel, when that load hits the back doors theyll never fit proper again. No powder coat no thanks. Ive seen enough. Thanks

Which excavator you use for the Mulcher

Way easier to do than the previous gen mkz.

Dealership wanted to charge me $620...guess we're breaking out the tools😂

Thank you sir!! Saved me money!! More mkz hybrid videos please!! I have a 2014!

Might I add,use a longer extention on your socket and using Teflon tape is not smart. Use thread sealant/pipe dope.

I came here today because my mother in laws Lincoln has made me crazy for far longer than it should have. I've tried the factory wrench, then a 3/4, 13/16, 19mm and 20mm and was left scratching my head in frustration. I like the tip on using the 8 point. I will be going to pic one up before going back at this again today. "How hard is it to change a wheel, I've done it many times before" was what I said more than 4 hours prior to this ordeal.

Can’t believe you have the exact same brand,model, year, and problem that I am having. I thought I was going crazy until I saw this video, wanted to do some research before I took a hammer to a 3/4 socket, so I turned to TH-cam and here you are! Thanks for sharing

Do you get a decent amount mulching jobs? I'm looking at a similar set up, would you recommend? Good ROI?

What are symptoms of it being bad

I replaced the knuckle on a lincoln mkx that was damaged in an accident with a ford edge knuckle and hub that said would fit but the hub diameter is just a little too big so doesnt allow wheel to sit on the hub the way it should. The old hub and bearing are fine thinking I could just swap them out but I didnt see bolts holding the hub on but might be behind the heat shield.

What quick couple is that? Just got a cat 303.5 and i need one and I like how that locks.

Poke a hole in the bottom of the oil filter and let it drain out. Less mess.

doesnt the bed come dimpled?

I have had two B&W gooseneck hitches and really like them. My one complaint is that, living on a dirt road, when the ball is stowed below the bed, it tends to get really nasty from the dust coating it (I grease before each use). As an alternative, I cut a wooden block to fill the square hole when the ball is not in use.

Good vid .cheers

Have you done a video on the rear?

Thanks

Please do another review

Thx my friend you gave me the confidence to do this job😊

Thanks for sharing this with us

Lincoln charges a hell of a lot more than $100-150 to do that job buddy I promise you that 😏✌️

Ur using the wrong weight oil read the owners manual

- neoprene gloves - 10 mm socket - T30 torx - 15 mm socket - 20ft/lb drain plug torque - 5.7 quarts 5W/30 fully synthetic -1348 napa gold filter

These are all season ? How do they preform in cold

Did my 2017 yesterday- the good old fashioned way: cardboard on concrete! So fulfilling... Get this- Had my last change done by my trusty local mom n' pop shop and musta had new guy- it was double-gasketed!!! How on earth did that not leak??? I will mention it if I have them do it again, but probably stick to doing it myself- as I usually do. Love those valves, great for if you accidentally over fill, or need to add some additive and remove a bit, but yes, they are slow. Still indispensable, but I forgot to get one to swap out on this rig. Next time. I also use clear tubing to route the oil closer to the pan- in windy conditions, it's imperative. That lift is gold!

🍀 *promosm*

For the torque - how certain are you that the axle nut goes back in at 147 ft/lbs of torque?

For the torque - how certain are you that the axle but goes back in at 146 ft/lbs of torque?

2" wheel spacers are a bad idea. In the UK you see maybe 3/4 inch spacers being fitted max.. anything more than that is a bit stupid

This is a much better design. No special tools needed to remove the bearings.

human ilness to keep everything stringent, spoiling biodiversity and making lots of co2 emission - so braindead as it can be😢😢

How many hrs on this head? How does it perform in blackberries?