วีดีโอ

I can oh so relate to that, thanks.

Gordon ramsey has a steak airfryer recipe. You just make a rub with aleppo p's and coffee grounds. (yes, coffee) Try it. Blew my mind, 2 ingredients

Make sure you install the ch340 usb to srial driver!!! Most every nano clone uses that instead of the cp2102

This entire video was you winging it. What an absolute crock of crap.

Fold the wide parts inward to produce a heavier mallet?

If you scrap a microwave for its asynchronous turntable motor, you could automate that fellow. Nice build

Dude! Your scrap and tools look like my shop but yours is definitely better organized. Why buy when we DIY? Exactly my thoughts. Subbed!!

Check this out .. I restored two Garland number three one. number five split face hammers.. I wish I would have found your channel before I did that. I paid up hard for those faces.. but the hammers turned out really nice.. thanks for sharing that trick man. Much appreciated stay safe out there man. . Very cool hack.

I have always wanted to try this. Im going to now. Thanks for taking us along 👍.

That's THE best use for that rawhide crap as it's known to cause huge health issues for dogs due to the chemicals used to make it... Lots of dogs being killed from investing them. Will keep an eye out for the rawhide chews in order to make up some mallets. Great video!!

After you trim the strip for the mallet you could cut the scraps into small pieces and boil them down to make a rawhide (collagen) glue that could be applied like wood glue before you roll the mallet head.

Take the strips that you cut off and add to both sides. Paper towels both sides to absorb moisture. Staple one end to board. Stretch as much as possible and staple opposite end same deal with sides. Paper, board, weight. Time. A couple of days later the medium will still be flexible but yielding. Roll as tightly as possible and use automotive hose clamps to further compress. Low temperature oven……. When it bounces back when dropped, probably ready for a coat of varnish to seal. Drill, handle, screw or dowel or brass rod or nail………😊

Rawhide from a chew toy-genius. To prevent the leather from starting to decompose, I'd change the water every day. Maybe hot water would soften it quicker? I would not add bleach-it can weaken fabric and bone so I'm sure it'd weaken leather. Probably dry it in a stove lowest setting once flattened. And I have no idea about this, just what iffing here-instead of epoxy, woodworking glue. Some types might be thin enough to pour. Hide glue you'd have to frost it like a cake then roll it up. Anything that helps hold furniture together should be tough! I'd be afraid the epoxy would make the hammer too hard, or would start to crack with extended use. Again-I could be wrong! The diy handles were great, and using the hose clamps. Vegan leather can be made from natural plant materials, but often it's just plastic, polyurethane, so be sure what you got. How about picking up a cheap leather purse from the thrift store and using that? Not rawhide, but would it make a hammer? Thanks for a great video!

You could tack it out flat on the board, as well....rawhide an be soaked repeatedly, to work it. Many of the Spanish Missions in California are built out of timbers lashed down with wet rawhide, that tightens up as it dries, and has lasted 100's of years....cured in part I'm sure by the candle smoke over the centuries.

Excellent work, looks like it will work well. Be interested in what your thoughts are after you use for a couple of projects, thanks for sharing your build and insights, enjoyed watching.

Why in the world didn’t I think of that, I have to get my mind outside the box a little more often. Nice job of fabricating, looks awesome, I will be trying that soon. I subscribed and liked, I too am interested in building my own tools as well as refurbishing and restoring old hand tools. Thanks for the video, enjoyed watching.

👍

Nice job, well done 👍

The ones buy in the store are covered some how with bees wax but I love the video

like a fool, I bought a like new used one on Fleabay for $15 and free shipping, think of all the time and money I could have saved doing this

This is the first 'craft' video I have seen that was based on a Shakespearean play "A Comedy Of Errors". :<) Like me, keep at it long enough and it may just come out right.

I always associate rawhide mallet to jewellery making, but i had to do a second take to realise that that wasn't a jewelers bench, really interesting to find who uses different tools and how Edit: if i remember correctly, the raw hide is tacked in place and bound with hoops

man this video is pretty relatable. i remember all the attempts i made at making rawhide mallets early on. i've made around a hundred or so now. a couple thoughts based on my experience: - most cured epoxy is quite hard, harder than the rawhide, which can leave marks on your work if you are working something delicate. i've left marks on silver with an epoxied mallet head as an example. - dog bones are usually made from the belly of the hide, which is the weakest and least dense part of the hide. it makes a softer, but faster wearing mallet. the rawhide near the spine makes the toughest mallets in my experience. - if you want a harder mallet, you can saturate the rawhide in either a very thin, slow curing epoxy like deep pour, cactus juice, or shellac. - stretch the rawhide on a board and nail down the edges. - put it into an oven at around 150-215°f until it becomes very dry. temperature takes some experimenting to get the exact effect you're after and see how the specific hide responds. - let the hide cool still stretched on the board - trim the dry hide to 20% oversized of what you want for final dimensions, it will move a fair bit as it soaks up whatever you are soaking it in. - submerge the rawhide in a container of liquid of choice. the very dry rawhide will readily soak up most things here and soften. as soon as it is softened enough, roll the head and wrap it in aluminum flashing or something similar with either parchment paper or a silicone release agent applied. - epoxy should cure on it's own without further intervention, but be wary of the leftover mix as it can heat up and cause a fire. the container for the epoxy should be a shallow container. deeper containers can cause the heat from catalyzation to run away and start a nasty fire. i don't like epoxy because it is usually too hard for my needs and is dangerous. - cactus juice is better than epoxy in my opinion. easier to work with and safer, you have to cure it in a toaster oven or something at around 200°f after it is saturated, but you aren't risking epoxy fires and cactus juice is meant for stabilizing wood so it works well. you can go the whole vacuum chamber route if you want to form the heads first and then impregnate them, but i've had good results with soaking the oven dried rawhide in cactus juice directly. it isn't as thick or difficult to penetrate as wood but ymmv. the downsides to cactus juice are how hard it is, and it only serves one purpose and can't really be reused. - shellac can be mixed in a 1lb cut or 2lb cut depending on how hard you want the final mallet. soak the oven dried and trimmed rawhide in a bucket of shellac for a few hours. i've forgotten and left mine a couple days once and it turned out fine. then remove it and roll and form the head on the aluminum flashing as usual. i like using a bunch of hoze clamps to make the final result more uniform. leave the head for a few days so the alcohol can evaporate letting the shellac resin harden. shellac makes the softest of the impregnation liquids i've tested, but you can get some shellac flakes when you are first using the mallet. i usually trim the head with a saw, sand it down and them beat on on something for a bit to break up the fibres at the face and around edges. that gets rid of any flaking and softens the face quite a bit. hope some of that was useful to someone.

can bearly hear you but your intro nearly deafened me. GREAT IDEA

👍✌

Very nice. By the way, where are you from

Good work

Nice work! Looks really clean.

hello thanks for your sharing and good ideas ! But, sorry to write this : be nice the sound is not good at all, you are too nervous and make too much wood shocking noises. If i may suggest, keep cool and calm. You will win a lot. Regards

This just saved me money. 👏

You're seriously inspiring. My Dad passed just shy of 70, a little over 5yrs ago. He was always busy playing in his band, and didn't really have much time to teach me anything at all, except for music. I've always loved to build & tinker around with stuff, and it's comforting & inspiring for me to watch your videos on how you create things. I have lock picking sets, I leather craft, work with wood a lot, mostly palettes, and glass. All of that I've had to teach myself, which hasn't been the greatest of things but it is what it is. Anyway, I thank you for the content you put out. It's funny that you used the old wiper blades, I always say there's a use for everything, and I'm terrible at throwing anything away for that reason. I look forward to more of your videos. Things that my father never taught me, well it's a comfort for me to learn from you and other creators. Thanks again, stay well & happy.

Hello, this was sort of what I was looking for, but before I lose my thought, instead of the putty you could've tried a double sided, double threaded hex nut, and it would've even given off a bit more height on the candles no? Was just a thought, I dabble in making lamps out of things, wine bottles, stuff like that. So my thought today was, building an electric candelabra, and while I was thinking about the base to use I stumbled onto your vid. Good stuff, thanks for the vid.

Looked pretty clean. The 50s is definitely vintage rather than antique. Antique usually means at least 100 years old. Less than that is vintage. In some specific markets and categories of collection it can be a different number, but those are the exception.

For gap filling use resin UV the kind used for jewelry making, it set with just a UV flashlight. I use thick CA for strong bond printed parts really do not need that kind of strength

Ohhhh your good bud!!

Hi all, over 90% of the viewers of my videos are not subscribers. Can we get that number down? Please subscribe to this channel. I doesn't cost anything.

Hi all, over 90% of the viewers of my videos are not subscribers. Can we get that number down? Please subscribe to this channel. I doesn't cost anything.

Hi all, over 90% of the viewers of my videos are not subscribers. Can we get that number down? Please subscribe to this channel. I doesn't cost anything.

Hi All, over 90% of the viewers of my videos are not subscribers. Can we get that number down? Please subscribe to this channel. I doesn't cost anything.

Hi all, over 90% of the viewers of my videos are not subscribers. Can we get that number down? Please subscribe to this channel. I doesn't cost anything.

Hi all, over 90% of the viewers of my videos are not subscribers. Can we get that number down? Please subscribe to this channel. I doesn't cost anything.

Hi all, over 90% of the viewers of my videos are not subscribers. Can we get that number down? Please subscribe to this channel. I doesn't cost anything.

Hi all, over 90% of the viewers of my videos are not subscribers. Can we get that number down? Please subscribe to this channel. I doesn't cost anything.

What are your thoughts on just shaping one layer of foam to the profile and then doing the glue up? Might be easier with the hot wire. Just my thoughts and observation.

I dont think carbonating vodka should do any harm to the soda stream as it contains mostly water and alcohol. Alcohol just evaporates leaving no traces of syrup etc.

Hi ! Following you fron France !!... this is what I was looking for !!!! Thank you so much !... this is a great job and I will try to make it !!... only one thing I was wondering... what (approximately) is the thickness of the plywood please ? Thanks ! Keep up the good work ! 👍👍

Great setup; great ideas, can’t wait for the next lesson

I would like to see a Gloop added to the test bed. Never liked the E6000, it seemed to have a lot of issues.

You’re hired! Bring me a sample.

Send some this way