วีดีโอ

電圧(電池の数を増やしたり)をupして地球ゴマの回転数をもっと上げるとどうなるかな？

90度傾けて浮かせればジャイロコンパスらしくはなる

凄い!想像力を膨らませる

ｼﾃ...ｺﾛｼﾃ...

これを何個か組み合わせて反重力装置が作れるのでは?と思った、遠い昔...。

別にぼっ…勃起とかしてねーし

母親って、結局はこういうことなんだろうね

バカっぽく見えて、どんなに重くしても倒れないからとても理にかなった動画！

遂にやりやがった

てこのげんり！

地球ゴマにモーターを付けるという発想がなかった

ここのコメント意味不明すぎる

Could you share with me the circuit and code implemented?

片側だけで吊ってる時の重さが 半分なのかが気になります

これ地味にＵＦＯの内部解明してる大発見だよな

永久機関？

おお～～凄い！

Hello there, nice video, I have the same your arduino board and MPU6050 sensor, could you please share your multiwii code and pin connection. thank you, my email is tutk@outlook.com

慣性の法則乙ｗ

リアクションホイールだなｗｗｗ

hi. im also trying by arduino uno uploaded a multiwii cord 2_4. and also i equipped the gy521(mpu6050). Anyway i operated the processing program. but the drone yaw axis is rolling when i connect. the yaw axis is rolling 5 degrees to clock wise. do you know what problumsb it is? or tell me what kind of version you use? for me multiwii 2.4 controlp5 2.0.4 processing 2.2.1

どうやって 作ります?

I am a noob so please forgive me if this question is already answered and feel free to delete the post. I have setup a flight controller myself per the website goo.gl/XxiU97 I would not expect you to go through the website and find out what I did. I will try to list it out. Hardware ------------ Arduino Pro Mini 5V 16MHz. GY521 MPU6050 Acc/Gyro No other hardware is connected as of yet including the receiver. These two connected each other as "A4<>SDA" and A5 <> "SCL". Power up the Arduino Pro mini/gy521 MPU6050 using the 5V output from the serial device FTDI chip. Screen print is here goo.gl/T5qRj2 The changes done to the multiwii program v2.4 MULTIWII software are listed below 1)Open the Multiwii.ino inside the Multiwii Folder once done go to the tabs within the arduino program and go to "config.h" this is where you will start 2)Enable QUADX mode 3)scroll down and uncomment #define MINTHROTTLE 1064 if you are using SimonK ESC and add //to the default setting which is #define MINTHROTTLE 1150 // (*) (**) 4)scroll down a little #define MAXTHROTTLE 2000 5)#define I2C_SPEED 400000L 6)Enabled GY521 MPU6050 7). UPLOAD! Multiwii Config UI is used to see the data coming in from MPU 6050 (The flight controller is is on the table steady and untouched). 1)Gyro data seems to be settled on (0,0,0) but the accelerator is constantly changing. Screen print is here db.tt/LSt4XDmU 2)Yaw is constantly changing in the clockwise direction. Could you please tell me why the Yaw is not stabilizing also give me a shout if you have questions. Thanks, M

なんか怖いw

How you get this graphs from necomimi?? can you give us the circuit?

Hi this is the part of arming in the source code: /******************************** ARM/DISARM *********************************/ /* optionally disable stick combinations to arm/disarm the motors. * In most cases one of the two options to arm/disarm via TX stick is sufficient */ #define ALLOW_ARM_DISARM_VIA_TX_YAW //#define ALLOW_ARM_DISARM_VIA_TX_ROLL and in MW conf app on PC my yaw change from 1000 to 2000 but my board isn't arm!! can you help me?

hi ! you have the diagrams? and sketch? sorry my english jejejej

すごいです！

Hi! Can you tell me what kind of resistors and capacitors you put between the imu and the ardunio mini?